AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 282

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
25.9.5
Name:
Access Type:
Offset:
Reset value:
• PERIOD: Transmit Period Divider Selection
This field selects the divider to apply to the selected Transmit Clock to generate a new Frame Sync Signal. If 0, no period
signal is generated. If not 0, a period signal is generated at each 2 x (PERIOD+1) Transmit Clock.
• STTDLY: Transmit Start Delay
If STTDLY is not 0, a delay of STTDLY clock cycles is inserted between the start event and the actual start of transmission
of data. When the Transmitter is programmed to start synchronously with the Receiver, the delay is also applied.
Note: STTDLY must be set carefully. If STTDLY is too short in respect to TAG (Transmit Sync Data) emission, data is emit-
ted instead of the end of TAG.
• START: Transmit Start Selection
31
23
15
–
7
0x8 - 0xF
START
Transmit Clock Mode Register
0x0
0x1
0x2
0x3
0x4
0x5
0x6
0x7
CKG
30
22
14
TCMR
Read/Write
0x18
0x00000000
–
6
Transmit Start
Continuous, as soon as a word is written in the THR Register (if Transmit is enabled), and immediately
after the end of transfer of the previous data.
Receive start
Detection of a low level on TX_FRAME_SYNC signal
Detection of a high level on TX_FRAME_SYNC signal
Detection of a falling edge on TX_FRAME_SYNC signal
Detection of a rising edge on TX_FRAME_SYNC signal
Detection of any level change on TX_FRAME_SYNC signal
Detection of any edge on TX_FRAME_SYNC signal
Reserved
CKI
29
21
13
–
5
28
20
12
–
4
PERIOD
STTDLY
CKO
27
19
11
3
26
18
10
2
START
25
17
9
1
AT32UC3A
CKS
24
16
8
0
282