AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 299

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
26. Universal Synchronous/Asynchronous Receiver/Transmitter (USART)
26.1
26.2
Features
Overview
Rev. 4.0.0.2
•
•
•
•
•
•
•
•
The Universal Synchronous Asynchronous Receiver Transceiver (USART) provides one full
duplex universal synchronous asynchronous serial link. Data frame format is widely programma-
ble (data length, parity, number of stop bits) to support a maximum of standards. The receiver
implements parity error, framing error and overrun error detection. The receiver time-out enables
handling variable-length frames and the transmitter timeguard facilitates communications with
slow remote devices. Multidrop communications are also supported through address bit han-
dling in reception and transmission.
The USART features three test modes: remote loopback, local loopback and automatic echo.
The USART supports specific operating modes providing interfaces on RS485 and SPI buses,
with ISO7816 T = 0 or T = 1 smart card slots and infrared transceivers. The hardware handshak-
ing feature enables an out-of-band flow control by automatic management of the pins RTS and
CTS.
The USART supports the connection to the Peripheral DMA Controller, which enables data
transfers to the transmitter and from the receiver. The PDC provides chained buffer manage-
ment without any intervention of the processor.
Programmable Baud Rate Generator
5- to 9-bit Full-duplex Synchronous or Asynchronous Serial Communications
RS485 with Driver Control Signal
ISO7816, T = 0 or T = 1 Protocols for Interfacing with Smart Cards
IrDA Modulation and Demodulation
SPI Mode
Test Modes
Supports Connection of Two Peripheral DMA Controller Channels (PDC)
– 1, 1.5 or 2 Stop Bits in Asynchronous Mode or 1 or 2 Stop Bits in Synchronous Mode
– Parity Generation and Error Detection
– Framing Error Detection, Overrun Error Detection
– MSB- or LSB-first
– Optional Break Generation and Detection
– By 8 or by 16 Over-sampling Receiver Frequency
– Optional Hardware Handshaking RTS-CTS
– Receiver Time-out and Transmitter Timeguard
– Optional Multidrop Mode with Address Generation and Detection
– NACK Handling, Error Counter with Repetition and Iteration Limit
– Communication at up to 115.2 Kbps
– Master or Slave
– Serial Clock Programmable Phase and Polarity
– SPI Serial Clock (CLK) Frequency up to Internal Clock Frequency CLK_USART/4
– Remote Loopback, Local Loopback, Automatic Echo
– Offers Buffer Transfer without Processor Intervention
AT32UC3A
299