AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 317

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
Figure 26-17. Manchester Encoded Characters RF Transmission
Figure 26-18. ASK Modulator Output
Uptstream Frequency F0
ASK Modulator
unipolar output
default polarity
NRZ stream
Manchester
Downstream
Upstream
encoded
Output
Emitter
Receiver
data
Fdown frequency Carrier
Fup frequency Carrier
Txd
1
The USART module is configured as a Manchester encoder/decoder. Looking at the down-
stream communication channel, Manchester encoded characters are serially sent to the RF
emitter. This may also include a user defined preamble and a start frame delimiter. Mostly, pre-
amble is used in the RF receiver to distinguish between a valid data from a transmitter and
signals due to noise. The Manchester stream is then modulated. See
for an example of ASK modulation scheme. When a logic one is sent to the ASK modulator, the
power amplifier, referred to as PA, is enabled and transmits an RF signal at downstream fre-
quency. When a logic zero is transmitted, the RF signal is turned off. If the FSK modulator is
activated, two different frequencies are used to transmit data. When a logic 1 is sent, the modu-
lator outputs an RF signal at frequency F0 and switches to F1 if the data sent is a 0. See
26-19 on page
From the receiver side, another carrier frequency is used. The RF receiver performs a bit check
operation examining demodulated data stream. If a valid pattern is detected, the receiver
switches to receiving mode. The demodulated stream is sent to the Manchester decoder.
Because of bit checking inside RF IC, the data transferred to the microcontroller is reduced by a
user-defined number of bits. The Manchester preamble length is to be defined in accordance
with the RF IC configuration.
318.
0
downstream transmitter
Upstream Receiver
RF filter
control
RF filter
control
Demod
VCO
VCO
ASK/FSK
LNA
Mod
PA
ASK/FSK
0
bi-dir
line
Configuration
Manchester
Manchester
decoder
encoder
Interface
Serial
Figure 26-18 on page 317
1
AT32UC3A
Receiver
USART
USART
Emitter
Figure
317