AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 323

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
Figure 26-24. Receiver Time-out Block Diagram
RETTO
Character
Received
STTTO
• Obtain an interrupt while no character is received. This is performed by writing CR with the
If STTTO is performed, the counter clock is stopped until a first character is received. The idle
state on RXD before the start of the frame does not provide a time-out. This prevents having to
obtain a periodic interrupt and enables a wait of the end of frame when the idle state on RXD is
detected.
If RETTO is performed, the counter starts counting down immediately from the value TO. This
enables generation of a periodic interrupt so that a user time-out can be handled, for example
when no key is pressed on a keyboard.
Figure 26-24 on page 323
Table 26-8 on page 323
Table 26-8.
handle an interrupt before a character is received and allows waiting for the next idle state on
RXD after a frame is received.
RETTO (Reload and Start Time-out) bit at 1. If RETTO is performed, the counter starts
counting down immediately from the value TO. This enables generation of a periodic interrupt
so that a user time-out can be handled, for example when no key is pressed on a keyboard.
1
D
Baud Rate
200000
bit/sec
14400
19200
28800
33400
56000
57600
1 200
2 400
4 800
9 600
Clear
600
Q
Baud Rate
Maximum Time-out Period
Clock
gives the maximum time-out period for some standard baud rates.
shows the block diagram of the Receiver Time-out feature.
Clock
16-bit Time-out
Counter
TO
Bit Time
1 667
Load
833
417
208
104
µs
69
52
35
30
18
17
5
16-bit
Value
0
=
TIMEOUT
Time-out
109 225
AT32UC3A
54 613
27 306
13 653
6 827
4 551
3 413
2 276
1 962
1 170
1 138
328
ms
323