UPD78F0413GA-GAM-AX NEC, UPD78F0413GA-GAM-AX Datasheet - Page 105

• Manufacturer Part Number: UPD78F0413GA-GAM-AX
• Description: 8BIT UC, 32K FLASH, 1KB RAM, LCD
• Manufacturer: NEC

Specifications of UPD78F0413GA-GAM-AX

• Controller Family/series: UPD78F
• No. Of I/o's: 30
• Ram Memory Size: 1024Byte
• Cpu Speed: 10MHz
• No. Of Timers: 8
• No. Of Pwm: RoHS Compliant
• Core Size: 8bit
• Program Memory Size: 32KB
• Oscillator Type: External, Internal

SEG output
selection
Digital/Analog
selection
Remarks 1. :
Notes 1.
PF2
2.
3.
4.
5.
6.
7.
8.
9.
2. The functions within arrowheads (< >) can be assigned by setting the input switch control register
3. X1, X2 pins can be used as on-chip debug mode setting pins (OCD0A, OCD0B) when the on-chip
The functions of the P20/ANI0 to P25/ANI5 pins are determined according to the settings of port
function register 2 (PF2), A/D port configuration register 0 (ADPC0), port mode register 2 (PM2),
analog input channel specification register (ADS).
Note
When using the P121 to P124 pins to connect a resonator for the main system clock (X1, X2) or
subsystem clock (XT1, XT2), or to input an external clock for the main system clock (EXCLK), the X1
oscillation mode, XT1 oscillation mode, or external clock input mode must be set by using the clock
operation mode select register (OSCCTL) (for details, see 5.3 (1) Clock operation mode select
register (OSCCTL) and (3) Setting of operation mode for subsystem clock pin). The reset value
of OSCCTL is 00H (all of the P121 to P124 are Input port pins).
Targeted at registers corresponding to each port.
RxD6 can be set as the input source for TI000 by setting ISC1 = 1.
Input enable of TM52 via TMH2 can be controlled by setting ISC2 = 1.
RxD6 can be set as the input source for INTP0 by setting ISC0 = 1.
When the P40/KR0/V
another bias method, it is used for the port function (P40) or the key interrupt function (KR0).
Set PF13 = 0 when using as port function.
PD78F041x only.
Table 4-6. Setting Functions of P20/SEG21/ANI0
PM
P
(ISC).
debug function is used. For detail, see CHAPTER 25 ON-CHIP DEBUG FUNCTION.
:
Analog input
selection
:
Digital I/O
selection
: Port mode register
ADPC0
PD78F041x only.
Does not apply.
Don’t care
Port output latch
Note
LC3
Input mode
Output mode
Input mode
Output mode
pin is set to the 1/4 bias method, it is used as V
CHAPTER 4 PORT FUNCTIONS
PM2
User’s Manual U18698EJ1V0UD
Does not select
ANI.
Selects ANI.
ADS
Note
to P25/SEG16/ANI5
Digital input
Digital output
Segment outpu
Analog input (not to be converted)
Analog input (to be converted by successive
approximation type A/D converter)
Setting prohibited
P25/SEG16/ANI5
P20/SEG21/ANI0
LC3
Note
. When the pin is set to
Pins
Note
Note
Pins
to
105