S912XEP768J5MAGR Freescale Semiconductor, S912XEP768J5MAGR Datasheet - Page 697

• Manufacturer Part Number: S912XEP768J5MAGR
• Description: 16-bit Microcontrollers - MCU 16-bit 768K Flash
• Manufacturer: Freescale Semiconductor

Specifications of S912XEP768J5MAGR

• Rohs: yes
• Core: HCS12X
• Processor Series: MC9S12
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 768 KB
• Data Ram Size: 48 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3.3 V to 5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-144
• Mounting Style: SMD/SMT

An exception to this is when channels are concatenated. Once concatenated mode is enabled (CONxx bits
set in PWMCTL register), enabling/disabling the corresponding 16-bit PWM channel is controlled by the
low order PWMEx bit.In this case, the high order bytes PWMEx bits have no effect and their
corresponding PWM output lines are disabled.
While in run mode, if all eight PWM channels are disabled (PWME7–0 = 0), the prescaler counter shuts
off for power savings.
Read: Anytime
Write: Anytime
Freescale Semiconductor
Module Base + 0x0000
PWME7
PWME6
PWME5
PWME4
PWME3
PWME2
Reset
Field
7
6
5
4
3
2
W
R
PWME7
Pulse Width Channel 7 Enable
0 Pulse width channel 7 is disabled.
1 Pulse width channel 7 is enabled. The pulse modulated signal becomes available at PWM output bit 7 when
Pulse Width Channel 6 Enable
0 Pulse width channel 6 is disabled.
1 Pulse width channel 6 is enabled. The pulse modulated signal becomes available at PWM output bit6 when
Pulse Width Channel 5 Enable
0 Pulse width channel 5 is disabled.
1 Pulse width channel 5 is enabled. The pulse modulated signal becomes available at PWM output bit 5 when
Pulse Width Channel 4 Enable
0 Pulse width channel 4 is disabled.
1 Pulse width channel 4 is enabled. The pulse modulated signal becomes available at PWM, output bit 4 when
Pulse Width Channel 3 Enable
0 Pulse width channel 3 is disabled.
1 Pulse width channel 3 is enabled. The pulse modulated signal becomes available at PWM, output bit 3 when
Pulse Width Channel 2 Enable
0 Pulse width channel 2 is disabled.
1 Pulse width channel 2 is enabled. The pulse modulated signal becomes available at PWM, output bit 2 when
0
7
its clock source begins its next cycle.
its clock source begins its next cycle. If CON67=1, then bit has no effect and PWM output line 6 is disabled.
its clock source begins its next cycle.
its clock source begins its next cycle. If CON45 = 1, then bit has no effect and PWM output bit4 is disabled.
its clock source begins its next cycle.
its clock source begins its next cycle. If CON23 = 1, then bit has no effect and PWM output bit2 is disabled.
PWME6
0
6
Figure 19-3. PWM Enable Register (PWME)
MC9S12XE-Family Reference Manual Rev. 1.25
Table 19-2. PWME Field Descriptions
PWME5
0
5
PWME4
0
4
Description
PWME3
0
3
Chapter 19 Pulse-Width Modulator (S12PWM8B8CV1)
PWME2
0
2
PWME1
0
1
PWME0
0
0
697