AT91SAM7X256B-CU Atmel, AT91SAM7X256B-CU Datasheet - Page 28

• Manufacturer Part Number: AT91SAM7X256B-CU
• Description: IC MCU 256KB FLASH 100TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X256B-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: 91S
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: CAN, Ethernet, SPI, I2S, TWI, USART, USB
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 3
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Package: 100TFBGA
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 55 MHz
• On-chip Adc: 8-chx10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

9.3
9.4
28
Power Management Controller
Advanced Interrupt Controller
AT91SAM7X512/256/128 Preliminary
The Power Management Controller uses the Clock Generator outputs to provide:
The Master Clock (MCK) is programmable from a few hundred Hz to the maximum operating fre-
quency of the device.
The Processor Clock (PCK) switches off when entering processor idle mode, thus allowing
reduced power consumption while waiting for an interrupt.
Figure 9-3.
• the Processor Clock PCK
• the Master Clock MCK
• the USB Clock UDPCK
• all the peripheral clocks, independently controllable
• four programmable clock outputs
• Controls the interrupt lines (nIRQ and nFIQ) of an ARM Processor
• Individually maskable and vectored interrupt sources
• 8-level Priority Controller
– Source 0 is reserved for the Fast Interrupt Input (FIQ)
– Source 1 is reserved for system peripherals (RTT, PIT, EFC, PMC, DBGU, etc.)
– Other sources control the peripheral interrupts or external interrupts
– Programmable edge-triggered or level-sensitive internal sources
– Programmable positive/negative edge-triggered or high/low level-sensitive external
– Drives the normal interrupt nIRQ of the processor
– Handles priority of the interrupt sources
sources
Power Management Controller Block Diagram
MAINCK
PLLCK
MAINCK
SLCK
PLLCK
SLCK
PLLCK
Master Clock Controller
Programmable Clock Controller
/1,/2,/4,...,/64
Prescaler
USB Clock Controller
/1,/2,/4,...,/64
ON/OFF
Divider
/1,/2,/4
Prescaler
Processor
Controller
Idle Mode
Clock Controller
Clock
Peripherals
ON/OFF
int
UDPCK
PCK
MCK
periph_clk[2..18]
pck[0..3]
6120H–ATARM–17-Feb-09