LPC2470FET208,551 NXP Semiconductors, LPC2470FET208,551 Datasheet - Page 115

• Manufacturer Part Number: LPC2470FET208,551
• Description: IC ARM7 MCU LCD 208-TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2470FET208,551

• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Type: ROMless
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/SPI/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB2470U
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Operating Supply Voltage: 3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4362; 935284071551; LPC2470FET208-S

NXP Semiconductors
UM10237_4
User manual
3.10 Vector Priority Registers 0-31 (VICVectPriority0-31 - 0xFFFF F200 to
3.12 Software Priority Mask Register (VICSWPriorityMask - 0xFFFF F024)
3.11 Vector Address Register (VICAddress - 0xFFFF FF00)
Table 111. Vector Address registers 0-31 (VICVectAddr0-31 - addresses 0xFFFF F100 to
27C)
These registers select a priority level for the 32 vectored IRQs. There are 16 priority
levels, corresponding to the values 0 through 15 decimal, of which 15 is the lowest priority.
The reset value of these registers defaults all interrupt to the lowest priority, allowing a
single write to elevate the priority of an individual interrupt.
Table 112. Vector Priority registers 0-31 (VICVectPriority0-31 - addresses 0xFFFF F200 to
When an IRQ interrupt occurs, the address of the Interrupt Service Routine (ISR) for the
interrupt that is to be serviced can be read from this register. The address supplied is from
one of the Vector Address Registers (VICVectAddr0-31).
Table 113. Vector Address register (VICAddress - address 0xFFFF FF00) bit description
The Software Priority Mask Register contains individual mask bits for the 16 interrupt
priority levels.
Bit
31:0 VICVectAddr The VIC provides the contents of one of these registers in
Bit
3:0
31:4 -
Bit
31:0 VICAddress Contains the address of the ISR for the currently active interrupt. This
Symbol
Symbol
VICVectPriority Selects one of 16 priority levels for the corresponding vectored
Symbol
0xFFFF F17C) bit description
0xFFFF F27C) bit description
Description
register must be written (with any value) at the end of an ISR, to
update the VIC priority hardware. Writing to the register at any other
time can cause incorrect operation.
response to a read of the Vector Address register (VICAddress
see
Description
register (one of the 32 VICVectAddr registers) that
corresponds to the interrupt that is to be serviced is read from
VICAddress whenever an interrupt occurs.
Description
interrupt.
Reserved, user software should not write ones to reserved bits. The
value read from a reserved bit is not defined.
Rev. 04 — 20 August 2009
Section
Chapter 7: LPC24XX Vectored Interrupt Controller (VIC)
7–3.9). The contents of the specific VICVectAddr
UM10237
© NXP B.V. 2009. All rights reserved.
Reset value
0x0000 0000
115 of 792
Reset
value
0
Reset
value
0xF
NA