PIC18F24J11 MICROCHIP [Microchip Technology], PIC18F24J11 Datasheet - Page 291

• Manufacturer Part Number: PIC18F24J11
• Description: 28/44-Pin, Low-Power, High-Performance USB Microcontrollers with nanoWatt XLP Technology
• Manufacturer: MICROCHIP [Microchip Technology]

19.5
The MSSP module in I
master and slave functions (including general call
support), and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications and 7-bit and 10-bit addressing.
Two pins are used for data transfer:
• Serial Clock (SCLx) – RC3/SCK1/SCL1/RP14 or
• Serial Data (SDAx) – RC4/SDI1/SDA1/RP15 or
The user must configure these pins as inputs by setting
the associated TRIS bits.
FIGURE 19-7:
 2011 Microchip Technology Inc.
Note:
SDAx
SCLx
RD0/PMD0/SCL2
RD1/PMD1/SDA2
Only port I/O names are used in this diagram for
the sake of brevity. Refer to the text for a full list of
multiplexed functions.
I
2
C Mode
Read
Shift
Clock
MSb
SSPxADD reg
Address Mask
Stop bit Detect
Match Detect
SSPxBUF reg
SSPxSR reg
MSSPx BLOCK DIAGRAM
(I
Start and
2
2
C mode fully implements all
C™ MODE)
LSb
Write
Addr Match
Set, Reset
S, P bits
(SSPxSTAT reg)
Internal
Data Bus
PIC18F46J11 FAMILY
19.5.1
The MSSP module has six registers for I
These are:
• MSSPx Control Register 1 (SSPxCON1)
• MSSPx Control Register 2 (SSPxCON2)
• MSSPx Status Register (SSPxSTAT)
• Serial Receive/Transmit Buffer Register
• MSSPx Shift Register (SSPxSR) – Not directly
• MSSPx Address Register (SSPxADD)
• MSSPx 7-Bit Address Mask Register (SSPxMSK)
SSPxCON1, SSPxCON2 and SSPxSTAT are the
control and status registers in I
SSPxCON1 and SSPxCON2 registers are readable and
writable. The lower six bits of the SSPxSTAT are
read-only. The upper two bits of the SSPxSTAT are
read/write.
SSPxSR is the shift register used for shifting data in or
out. SSPxBUF is the buffer register to which data
bytes are written to or read from.
SSPxADD contains the slave device address when the
MSSP is configured in I
MSSP is configured in Master mode, the lower seven
bits of SSPxADD act as the Baud Rate Generator
(BRG) reload value.
SSPxMSK holds the slave address mask value when
the module is configured for 7-Bit Address Masking
mode. While it is a separate register, it shares the same
SFR address as SSPxADD; it is only accessible when
the SSPM<3:0> bits are specifically set to permit
access.
Section 19.5.3.4 “7-Bit Address Masking
In receive operations, SSPxSR and SSPxBUF
together, create a double-buffered receiver. When
SSPxSR receives a complete byte, it is transferred to
SSPxBUF and the SSPxIF interrupt is set.
During
double-buffered. A write to SSPxBUF will write to both
SSPxBUF and SSPxSR.
(SSPxBUF)
accessible
transmission,
Additional
REGISTERS
details
2
the
C Slave mode. When the
2
C mode operation. The
SSPxBUF
are
DS39932D-page 291
provided
2
C operation.
Mode”.
is
not
in