S912XEG128J2MAL Freescale Semiconductor, S912XEG128J2MAL Datasheet - Page 736

• Manufacturer Part Number: S912XEG128J2MAL
• Description: 16-bit Microcontrollers - MCU 16BIT 128K FLASH 16K RAM
• Manufacturer: Freescale Semiconductor

Specifications of S912XEG128J2MAL

• Rohs: yes
• Core: RISC
• Processor Series: HCS12X
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 128 KB
• Data Ram Size: 12 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-112
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 8
• Data Rom Size: 4 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• On-chip Dac: Yes
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 3.13 V

Chapter 20 Serial Communication Interface (S12SCIV5)
736
Field
OR
NF
FE
PF
3
2
1
0
Overrun Flag — OR is set when software fails to read the SCI data register before the receive shift register
receives the next frame. The OR bit is set immediately after the stop bit has been completely received for the
second frame. The data in the shift register is lost, but the data already in the SCI data registers is not affected.
Clear OR by reading SCI status register 1 (SCISR1) with OR set and then reading SCI data register low
(SCIDRL).
0 No overrun
1 Overrun
Note: OR flag may read back as set when RDRF flag is clear. This may happen if the following sequence of
Noise Flag — NF is set when the SCI detects noise on the receiver input. NF bit is set during the same cycle as
the RDRF flag but does not get set in the case of an overrun. Clear NF by reading SCI status register 1(SCISR1),
and then reading SCI data register low (SCIDRL).
0 No noise
1 Noise
Framing Error Flag — FE is set when a logic 0 is accepted as the stop bit. FE bit is set during the same cycle
as the RDRF flag but does not get set in the case of an overrun. FE inhibits further data reception until it is
cleared. Clear FE by reading SCI status register 1 (SCISR1) with FE set and then reading the SCI data register
low (SCIDRL).
0 No framing error
1 Framing error
Parity Error Flag — PF is set when the parity enable bit (PE) is set and the parity of the received data does not
match the parity type bit (PT). PF bit is set during the same cycle as the RDRF flag but does not get set in the
case of an overrun. Clear PF by reading SCI status register 1 (SCISR1), and then reading SCI data register low
(SCIDRL).
0 No parity error
1 Parity error
events occurs:
Event 3 may be at exactly the same time as event 2 or any time after. When this happens, a dummy
SCIDRL read following event 4 will be required to clear the OR flag if further frames are to be received.
1. After the first frame is received, read status register SCISR1 (returns RDRF set and OR flag clear);
2. Receive second frame without reading the first frame in the data register (the second frame is not
3. Read data register SCIDRL (returns first frame and clears RDRF flag in the status register);
4. Read status register SCISR1 (returns RDRF clear and OR set).
received and OR flag is set);
Table 20-11. SCISR1 Field Descriptions (continued)
MC9S12XE-Family Reference Manual Rev. 1.25
Description
Freescale Semiconductor