ATAVRSB202 Atmel, ATAVRSB202 Datasheet - Page 118
ATAVRSB202
Manufacturer Part Number
ATAVRSB202
Description
KIT BATT MGMT FOR ATMEGA32HVB
Manufacturer
Atmel
Specifications of ATAVRSB202
Main Purpose
*
Embedded
*
Utilized Ic / Part
*
Primary Attributes
*
Secondary Attributes
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 118 of 275
- Download datasheet (7Mb)
20.3.1
8042B–AVR–06/10
Configuring PA1 and PA0 for V-ADC operation
Power-off mode. Note that the bandgap voltage reference must be enabled and disabled sepa-
rately, see
Figure 20-2. Voltage ADC Conversion Diagram
To perform a V-ADC conversion, the analog input channel must first be selected by writing to the
VADMUX register. When a logical one is written to the V-ADC Start Conversion bit VADSC, a
conversion of the selected channel will start. The VADSC bit stays high as long as the conver-
sion is in progress and will be cleared by hardware when the conversion is completed. When a
conversion is in progress, the V-ADC Data Register - VADCL and VADCH will be invalid. If the
System Clock Prescaler setting is changed during a V-ADC conversion, the conversion will be
aborted. If a different data channel is selected while a conversion is in progress, the ADC will fin-
ish the current conversion before performing the channel change. When a conversion is finished
the V-ADC Conversion Complete Interrupt Flag – VADCCIF is set. One 12-bit conversion takes
519 µs to complete from the start bit is set to the interrupt flag is set. The V-ADC Data Register -
VADCL and VADCH will be valid until a new conversion is started. To ensure that correct data is
read, both high and low byte data registers should be read before starting a new conversion.
When one of the single ended channels ADC0 or ADC1 is used as analog input to the VADC,
either PA0 or PA1 are used as signal ground (SGND). When ADC0/1 is selected as input chan-
nel, PA1/0 is automatically switched to SGND.
The use of PA1 and PA0 as SGND is efficient for the thermistor configuration shown in
ing Circuit” on page
divider resistor, R31, to PA0 and PA1 respectively.
Both PA0 and PA1 have very high input impedance when used as ADC inputs, which makes it
possible to connect two thermistors in the configuration, shown in
225. However, input impedance is limited and if high accuracy is required, only one thermistor
should be connected between PA0 and PA1. If two thermistors are connected, the configuration
is as follows:
• When measuring RT33, PA1 should be used as input channel and PA0 is automatically
• When measuring RT32, PA0 should be used as input channel and PA1 is automatically
Conversion Result
switched to SGND.
switched to SGND.
Start Conversion
Interrupt
”Bandgap Calibration” on page
OLD DATA
225. Both thermistors, RT32 and RT33 are connected through a common
INVALID DATA
124.
V A L I D
ATmega16HVB/32HVB
D ATA
”Operating Circuit” on page
INVALID DATA
”Operat-
118
Related parts for ATAVRSB202
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: