ATAVRSB202 Atmel, ATAVRSB202 Datasheet - Page 151
ATAVRSB202
Manufacturer Part Number
ATAVRSB202
Description
KIT BATT MGMT FOR ATMEGA32HVB
Manufacturer
Atmel
Specifications of ATAVRSB202
Main Purpose
*
Embedded
*
Utilized Ic / Part
*
Primary Attributes
*
Secondary Attributes
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 151 of 275
- Download datasheet (7Mb)
8042B–AVR–06/10
When the battery is started from a power-off condition by connecting a legal charger, SW should
determine whether to allow charging or not before enabling the C-FET. Before allowing charging
it is recommended to use the V-ADC to measure the cell temperature and cell voltages. Depend-
ing on the total cell voltage, the device should either start up in DUVR mode or in normal
charging mode with the C-FET and D-FET enabled.
• If the total cell voltage is below 4.5V, the battery should enter DUVR charging mode. This
• If the total cell voltage is above 4.5V, the battery should enter normal charging mode with both
The
charging 3 deeply discharged Li-ion cells in series using DUVR mode.
Figure 25-3. DUVR mode charging in 3-cell mode configuration
1. A charger with 12.6V charge voltage is plugged to the Pack+ pin and the
2. The ATmega16HVB/32HVB exit reset and initializes modules. To determine if charging
3. D-FET is enabled and the VFET voltage increase to the Pack+ level.
4. DUVR mode is entered by clearing the DUVRD bit in FCSR. The VFET voltage and the
5. The total cell voltage has reached the regulated VFET limit and VFET follows the cell
ensures safe operation voltage while allowing charging.
C-FET and D-FET enabled.
need to ensure to exit DUVR mode and enable the C-FET before the charger sees this
limit.
ATmega16HVB/32HVB enters reset mode. Charger should be configured with a charge
current limit (pre-charge current).
should be allowed and if DUVR mode should be entered, cell temperature and cell volt-
ages are measured by the V-ADC.
Pack+ voltage will now be regulated to approximately 4.5V.
voltage as the battery is charged.
”DUVR mode charging in 3-cell mode configuration” on page 151
14
12
10
8
6
4
2
0
1 2
3
4
5 6
ATmega16HVB/32HVB
shows an example of
7
RESET
DUVRD
CFE
DFE
PVT
Pack+
151
Related parts for ATAVRSB202
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: