YR0K42378FC000BA Renesas Electronics America, YR0K42378FC000BA Datasheet - Page 920
YR0K42378FC000BA
Manufacturer Part Number
YR0K42378FC000BA
Description
KIT EVAL FOR H8S/2378
Manufacturer
Renesas Electronics America
Series
H8®r
Type
MCUr
Datasheet
1.YR0K42378FC000BA.pdf
(1208 pages)
Specifications of YR0K42378FC000BA
Contents
Board
For Use With/related Products
H8S/2378
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 920 of 1208
- Download datasheet (8Mb)
Section 20 Flash Memory (0.35-μm F-ZTAT Version)
20.7.2
When erasing flash memory, the erase/erase-verify flowchart shown in figure 20.8 should be
followed.
1. Prewriting (setting erase block data to all 0s) is not necessary.
2. Erasing is performed in block units. Make only a single-bit specification in the erase block
3. The time during which the E bit is set to 1 is the flash memory erase time.
4. The watchdog timer (WDT) is set to prevent overprogramming due to program runaway, etc.
5. For a dummy write to a verify address, write 1-byte data H'FF to an address whose lower two
6. If the read data is not erased, set erase mode again, and repeat the erase/erase-verify sequence
20.7.3
All interrupts, including NMI input, are disabled when flash memory is being programmed or
erased, and while the boot program is executing in boot mode. There are three reasons for this:
1. Interrupt during programming or erasing might cause a violation of the programming or
2. If the interrupt exception handling is started when the vector address has not been programmed
3. If an interrupt occurred during boot program execution, it would not be possible to execute the
Rev.7.00 Mar. 18, 2009 page 852 of 1136
REJ09B0109-0700
registers (EBR1 and EBR2). To erase multiple blocks, each block must be erased in turn.
Set a value greater than (y + z + α + β) ms as the WDT overflow period.
bits are B'00. Verify data can be read in longwords from the address to which a dummy write
was performed.
as before. The maximum number of repetitions of the erase/erase-verify sequence (N) must
not be exceeded.
erasing algorithm, with the result that normal operation could not be assured.
yet or the flash memory is being programmed or erased, the vector would not be read correctly,
possibly resulting in CPU runaway.
normal boot mode sequence.
Erase/Erase-Verify
Interrupt Handling when Programming/Erasing Flash Memory
Related parts for YR0K42378FC000BA
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: