Z8F2480AN020SG Zilog, Z8F2480AN020SG Datasheet - Page 55

• Manufacturer Part Number: Z8F2480AN020SG
• Description: MCU 8BIT 24KB FLASH 44LQFP
• Manufacturer: Zilog
• Series: Encore!® XP®r

Specifications of Z8F2480AN020SG

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LED, LVD, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-LQFP
• Processor Series: Z8F248x
• Core: eZ8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 3
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: 770-1002 - ISP 4PORT ZILOG Z8 ENCORE! MCU269-4643 - KIT DEV Z8 ENCORE XP 28-PIN269-4630 - DEV KIT FOR Z8 ENCORE 8K/4K269-4629 - KIT DEV Z8 ENCORE XP 28-PIN269-4628 - KIT DEV Z8 ENCORE XP 8-PIN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4676

Low-Voltage Detection
PS025011-1010
Caution:
Stop Mode Recovery Using Comparator Interrupt
Stop Mode Recovery Using GPIO Port Pin Transition
Stop Mode Recovery Using External RESET Pin
If Comparator enabled for STOP mode operation interrupts during STOP mode, the device
undergoes a Stop Mode Recovery sequence. In the Reset Status Register, the
set to 1. If the Z8 Encore! XP F1680 Series device is configured to respond to interrupts,
the eZ8 CPU services the comparator interrupt request following the normal Stop Mode
Recovery sequence.
Each of the GPIO Port pins may be configured as a Stop Mode Recovery input source. 
On any GPIO pin enabled as a Stop Mode Recovery source, a change in the input pin
value (from high to low or from low to high) initiates Stop Mode Recovery. In the Reset
Status register, the
When the Z8 Encore! XP F1680 Series device is in STOP mode and the external RESET
pin is driven Low, a System Reset occurs. Because of a glitch filter operating on the
RESET pin, the low pulse must be greater than the minimum width specified, or it is
ignored. For details, see
In addition to the VBO Reset described earlier, it is also possible to generate an interrupt
when the supply voltage drops below a user-selected value. For more details on the 
available Low-Voltage Detection (LVD) threshold levels, see
page 273.
When the supply voltage drops below the LVD threshold, the
Register is set to 1. This bit remains 1 until the low-voltage condition elapses. Reading or
writing this bit does not clear it. The LVD circuit can also generate an interrupt when
enabled
the interrupt is the only way to guarantee detection of a transient low-voltage event.
The LVD circuit is either enabled or disabled by the Power Control Register bit 4. For
more details, see
In STOP mode, the GPIO Port Input Data registers (PxIN) are disabled. The Port Input
Data registers record the Port transition only if the signal stays on the Port pin till the
end of the Stop Mode Recovery delay. As a result, short pulses on the Port pin can
initiate Stop Mode Recovery without being written to the Port Input Data register or
without initiating an interrupt (if enabled for that pin).
(Interrupt Vectors and Priority
Power Control Register Definitions
STOP
Electrical Characteristics
bit is set to 1.
P R E L I M I N A R Y
on page 74). The LVD is not latched, so enabling
Reset, Stop Mode Recovery, and Low-Voltage
on page 339.
on page 47.
Z8 Encore! XP
Trim Bit Address 0000H
LVD
Product Specification
bit of the RSTSTAT
®
F1680 Series
STOP
bit is
on
41