MC9S08QG8CDTE Freescale Semiconductor, MC9S08QG8CDTE Datasheet - Page 170

• Manufacturer Part Number: MC9S08QG8CDTE
• Description: IC MCU 8K FLASH 10MHZ 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG8CDTE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 512Byte
• # I/os (max): 12
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• Package: 16TSSOP
• Family Name: HCS08
• Maximum Speed: 20 MHz
• For Use With: DEMO9S08QG8E - BOARD DEMO FOR MC9S08QG8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Inter-Integrated Circuit (S08IICV1)
11.4.1.8
The clock synchronization mechanism can be used as a handshake in data transfer. Slave devices may hold
the SCL low after completion of one byte transfer (9 bits). In such case, it halts the bus clock and forces
the master clock into wait states until the slave releases the SCL line.
11.4.1.9
The clock synchronization mechanism can be used by slaves to slow down the bit rate of a transfer. After
the master has driven SCL low the slave can drive SCL low for the required period and then release it. If
the slave SCL low period is greater than the master SCL low period then the resulting SCL bus signal low
period is stretched.
11.5
The IIC is disabled after reset. The IIC cannot cause an MCU reset.
11.6
The IIC generates a single interrupt.
An interrupt from the IIC is generated when any of the events in
is set. The interrupt is driven by bit IICIF (of the IIC status register) and masked with bit IICIE (of the IIC
control register). The IICIF bit must be cleared by software by writing a one to it in the interrupt routine.
The user can determine the interrupt type by reading the status register.
168
Resets
Interrupts
SCL1
SCL2
SCL
Handshaking
Clock Stretching
Match of received calling address
Complete 1-byte transfer
Interrupt Source
INTERNAL COUNTER RESET
Arbitration Lost
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
Figure 11-9. IIC Clock Synchronization
Table 11-8. Interrupt Summary
DELAY
Status
ARBL
IAAS
TCF
IICIF
IICIF
IICIF
Table 11-8
Flag
START COUNTING HIGH PERIOD
Local Enable
occur provided the IICIE bit
IICIE
IICIE
IICIE
Freescale Semiconductor