MC9S08QG8CDTE Freescale Semiconductor, MC9S08QG8CDTE Datasheet - Page 242

• Manufacturer Part Number: MC9S08QG8CDTE
• Description: IC MCU 8K FLASH 10MHZ 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG8CDTE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 512Byte
• # I/os (max): 12
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• Package: 16TSSOP
• Family Name: HCS08
• Maximum Speed: 20 MHz
• For Use With: DEMO9S08QG8E - BOARD DEMO FOR MC9S08QG8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Timer/Pulse-Width Modulator (S08TPMV2)
16.4.3
This type of PWM output uses the up-/down-counting mode of the timer counter (CPWMS = 1). The
output compare value in TPMCnVH:TPMCnVL determines the pulse width (duty cycle) of the PWM
signal and the period is determined by the value in TPMMODH:TPMMODL. TPMMODH:TPMMODL
should be kept in the range of 0x0001 to 0x7FFF because values outside this range can produce ambiguous
results. ELSnA will determine the polarity of the CPWM output.
If the channel value register TPMCnVH:TPMCnVL is zero or negative (bit 15 set), the duty cycle will be
0%. If TPMCnVH:TPMCnVL is a positive value (bit 15 clear) and is greater than the (nonzero) modulus
setting, the duty cycle will be 100% because the duty cycle compare will never occur. This implies the
usable range of periods set by the modulus register is 0x0001 through 0x7FFE (0x7FFF if generation of
100% duty cycle is not necessary). This is not a significant limitation because the resulting period is much
longer than required for normal applications.
TPMMODH:TPMMODL = 0x0000 is a special case that should not be used with center-aligned PWM
mode. When CPWMS = 0, this case corresponds to the counter running free from 0x0000 through 0xFFFF,
but when CPWMS = 1 the counter needs a valid match to the modulus register somewhere other than at
0x0000 in order to change directions from up-counting to down-counting.
Figure 16-12
determines the pulse width (duty cycle) of the CPWM signal. If ELSnA = 0, the compare match while
counting up forces the CPWM output signal low and a compare match while counting down forces the
output high. The counter counts up until it reaches the modulo setting in TPMMODH:TPMMODL, then
counts down until it reaches zero. This sets the period equal to two times TPMMODH:TPMMODL.
Center-aligned PWM outputs typically produce less noise than edge-aligned PWMs because fewer I/O pin
transitions are lined up at the same system clock edge. This type of PWM is also required for some types
of motor drives.
Because the HCS08 is a family of 8-bit MCUs, the settings in the timer channel registers are buffered to
ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers,
TPMMODH, TPMMODL, TPMCnVH, and TPMCnVL, actually write to buffer registers. Values are
240
Center-Aligned PWM Mode
shows the output compare value in the TPM channel registers (multiplied by 2), which
TPMMODH:TPMM
TPM1C
COUNT =
Figure 16-12. CPWM Period and Pulse Width (ELSnA = 0)
pulse width = 2 x (TPMCnVH:TPMCnVL)
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
period = 2 x (TPMMODH:TPMMODL);
(COUNT DOWN)
for TPMMODH:TPMMODL = 0x0001–0x7FFF
COMPARE
OUTPUT
2 x
2 x
PULSE WIDTH
COUNT = 0
PERIOD
(COUNT UP)
COMPARE
OUTPUT
TPMMODH:TPMM
COUNT =
Freescale Semiconductor
Eqn. 16-1
Eqn. 16-2