MC9S08QG8CDTE Freescale Semiconductor, MC9S08QG8CDTE Datasheet - Page 221

• Manufacturer Part Number: MC9S08QG8CDTE
• Description: IC MCU 8K FLASH 10MHZ 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG8CDTE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 512Byte
• # I/os (max): 12
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• Package: 16TSSOP
• Family Name: HCS08
• Maximum Speed: 20 MHz
• For Use With: DEMO9S08QG8E - BOARD DEMO FOR MC9S08QG8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

15.4.3
This register is used to set the prescaler and bit rate divisor for an SPI master. This register may be read or
written at any time.
Freescale Semiconductor
SPPR[2:0]
MODFEN
BIDIROE
SPISWAI
SPR[2:0]
Reset
SPC0
Field
Field
6:4
2:0
4
3
1
0
W
R
SPI Baud Rate Register (SPIBR)
Master Mode-Fault Function Enable — When the SPI is configured for slave mode, this bit has no meaning or
effect. (The SS pin is the slave select input.) In master mode, this bit determines how the SS pin is used (refer to
Table 15-2
0 Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI
1 Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output
Bidirectional Mode Output Enable — When bidirectional mode is enabled by SPI pin control 0 (SPC0) = 1,
BIDIROE determines whether the SPI data output driver is enabled to the single bidirectional SPI I/O pin.
Depending on whether the SPI is configured as a master or a slave, it uses either the MOSI (MOMI) or MISO
(SISO) pin, respectively, as the single SPI data I/O pin. When SPC0 = 0, BIDIROE has no meaning or effect.
0 Output driver disabled so SPI data I/O pin acts as an input
1 SPI I/O pin enabled as an output
SPI Stop in Wait Mode
0 SPI clocks continue to operate in wait mode
1 SPI clocks stop when the MCU enters wait mode
SPI Pin Control 0 — The SPC0 bit chooses single-wire bidirectional mode. If MSTR = 0 (slave mode), the SPI
uses the MISO (SISO) pin for bidirectional SPI data transfers. If MSTR = 1 (master mode), the SPI uses the MOSI
(MOMI) pin for bidirectional SPI data transfers. When SPC0 = 1, BIDIROE is used to enable or disable the output
driver for the single bidirectional SPI I/O pin.
0 SPI uses separate pins for data input and data output
1 SPI configured for single-wire bidirectional operation
SPI Baud Rate Prescale Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate prescaler
as shown in
drives the input of the SPI baud rate divider (see
SPI Baud Rate Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate divider as shown in
Table
divider is the SPI bit rate clock for master mode.
0
0
7
15-6. The input to this divider comes from the SPI baud rate prescaler (see
= Unimplemented or Reserved
for more details).
Table
SPPR2
0
6
15-5. The input to this prescaler is the bus rate clock (BUSCLK). The output of this prescaler
Table 15-4. SPIBR Register Field Descriptions
Table 15-3. SPIC2 Register Field Descriptions
Figure 15-7. SPI Baud Rate Register (SPIBR)
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
SPPR1
0
5
SPPR0
0
4
Figure
Description
Description
15-4).
3
0
0
SPR2
0
2
Serial Peripheral Interface (S08SPIV3)
Figure
15-4). The output of this
SPR1
0
1
SPR0
0
0
219