S9S12HY64J0MLH Freescale Semiconductor, S9S12HY64J0MLH Datasheet - Page 725

• Manufacturer Part Number: S9S12HY64J0MLH
• Description: MCU 64K FLASH AUTO 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12HY64J0MLH

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-LQFP
• Controller Family/series: S12
• No. Of I/o's: 50
• Ram Memory Size: 4KB
• Cpu Speed: 64MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: S12HY
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12HY64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1. Maximum leakage current occurs at maximum operating temperature. Current decreases by approximately one-half for each
2. Refer to
3. Parameter only applies in stop or pseudo stop mode.
A.1.10
This section describes the current consumption characteristics of the device as well as the conditions for
the measurements.
A.1.10.1
IDD value is measured on VDDR pin. It does not include the current to drive external loads. Unless
otherwise noted the currents are measured in special single chip mode and the CPU code is executed from
RAM. For Run and Wait current measurements PLL is on and the reference clock is the IRC1M trimmed
to 1MHz. The bus frequency is 32MHz and the CPU frequency is 64MHz. Table A-7., Table A-8. and
Table A-9. show the configuration of the CPMU module and the peripherals for Run, Wait and Stop current
measurement.
Freescale Semiconductor
18
19
8 C to 12 C in the temperature range from 50 C to 125 C.
D Port T, S, R, AD interrupt input pulse passed (STOP)
D IRQ pulse width, edge-sensitive mode (STOP)
Section A.1.4, “Current Injection”
Supply Currents
Table A-8. CPUM Configuration for Run/Wait and Full Stop Current Measurement
Measurement Conditions
CPMU REGISTER
CPMU REGISTER
CPMUPOSTDIV
CPMUSYNR
Table A-7. CPMU Configuration for Pseudo Stop Current Measurement
CPMUCLKS
CPMUCLKS
CPMUOSC
CPMUCOP
CPMUOSC
CPMURTI
MC9S12HY/HA-Family Reference Manual, Rev. 1.04
PLLSEL=0, PSTP=1,
PRE=PCE=RTIOSCSEL=COPOSCSEL=1
OSCE=1, External Square wave on EXTAL f
V
RTDEC=0, RTR[6:4]=111, RTR[3:0]=1111;
WCOP=1, CR[2:0]=111
VCOFRQ[1:0]=01,SYNDIV[5:0] = 32
POSTDIV[4:0]=0,
PLLSEL=1
OSCE=0,
Reference clock for PLL is f
Table A-6. 5-V I/O Characteristics
IH
for more details
= 1.8V, V
IL
=0V
Bit settings/Conditions
Bit settings/Conditions
PW
t
PULSE
IRQ
ref
=f
irc1m
4
1
trimmed to 1MHz
EXTAL
—
—
=16MHz,
Electrical Characteristics
—
—
tcyc
tcyc
725