UPD70F3735GC-GAD-AX Renesas Electronics America, UPD70F3735GC-GAD-AX Datasheet - Page 462

• Manufacturer Part Number: UPD70F3735GC-GAD-AX
• Description: MCU 32BIT V850ES/JX3-L 80-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Lr

Specifications of UPD70F3735GC-GAD-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 20MHz
• Connectivity: CSI, EBI/EMI, I²C, UART/USART
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 66
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 8x10b, D/A 1x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JF3-L
15.6.4 SBF reception
UAnCTL0.UAnRXE bit to 1.
detection is performed.
interrupt request signal (INTUAnR) is output. The UAnOPT0.UAnSRF bit is automatically cleared and SBF reception ends.
Error detection for the UAnSTR.UAnOVE, UAnSTR.UAnPE, and UAnSTR.UAnFE bits is suppressed and UART
communication error detection processing is not performed. Moreover, data transfer of the UARTAn reception shift register
and UAnRX register is not performed and FFH, the initial value, is held. If the SBF width is 10 or fewer bits, reception is
terminated as error processing without outputting an interrupt, and the SBF reception mode is returned to. The UAnSRF
bit is not cleared at this time.
R01UH0017EJ0400 Rev.4.00
Sep 30, 2010
The reception enabled status is achieved by setting the UAnCTL0.UAnPWR bit to 1 and then setting the
The SBF reception wait status is set by setting the SBF reception trigger (UAnOPT0.UAnSTR bit) to 1.
In the SBF reception wait status, similarly to the UART reception wait status, the RXDAn pin is monitored and start bit
Following detection of the start bit, reception is started and the internal counter counts up according to the set baud rate.
When a stop bit is received, if the SBF width is 11 or more bits, normal processing is judged and a reception complete
Cautions 1. If SBF is transmitted during a data reception, a framing error occurs.
(a) Normal SBF reception (detection of stop bit in more than 10.5 bits)
(b) SBF reception error (detection of stop bit in 10.5 or fewer bits)
2. Do not set the SBF reception trigger bit (UAnSRT) and SBF transmission trigger bit (UAnSTT) to 1
INTUAnR
interrupt
RXDAn
UAnSRF
during an SBF reception (UAnSRF = 1).
RXDAn
UAnSRF
INTUAnR
interrupt
1
1
CHAPTER 15 ASYNCHRONOUS SERIAL INTERFACE A (UARTA)
2
2
Figure 15-7. SBF Reception
3
3
4
4
5
5
11.5
6
10.5
6
7
7
8
8
9
9
10
10
11
Page 446 of 816