MC68908GZ8MFAE Freescale Semiconductor, MC68908GZ8MFAE Datasheet - Page 192

• Manufacturer Part Number: MC68908GZ8MFAE
• Description: IC MCU 8BIT 8K FLASH 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68908GZ8MFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Processor Series: M689xx
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, SCI, CAN
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 2
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Enhanced Serial Communications Interface (ESCI) Module
15.4.3.4 Framing Errors
If the data recovery logic does not detect a logic 1 where the stop bit should be in an incoming character,
it sets the framing error bit, FE, in SCS1. A break character also sets the FE bit because a break character
has no stop bit. The FE bit is set at the same time that the SCRF bit is set.
15.4.3.5 Baud Rate Tolerance
A transmitting device may be operating at a baud rate below or above the receiver baud rate.
Accumulated bit time misalignment can cause one of the three stop bit data samples to fall outside the
actual stop bit. Then a noise error occurs. If more than one of the samples is outside the stop bit, a framing
error occurs. In most applications, the baud rate tolerance is much more than the degree of misalignment
that is likely to occur.
As the receiver samples an incoming character, it resynchronizes the RT clock on any valid falling edge
within the character. Resynchronization within characters corrects misalignments between transmitter bit
times and receiver bit times.
Slow Data Tolerance
Figure 15-8
or a framing error. The slow stop bit begins at RT8 instead of RT1 but arrives in time for the stop bit data
samples at RT8, RT9, and RT10.
For an 8-bit character, data sampling of the stop bit takes the receiver 9 bit times × 16 RT cycles +
10 RT cycles = 154 RT cycles.
With the misaligned character shown in
the count of the transmitting device is 9 bit times × 16 RT cycles + 3 RT cycles = 147 RT cycles.
The maximum percent difference between the receiver count and the transmitter count of a slow 8-bit
character with no errors is:
For a 9-bit character, data sampling of the stop bit takes the receiver10 bit times × 16 RT cycles +
10 RT cycles = 170 RT cycles.
With the misaligned character shown in
the count of the transmitting device is 10 bit times × 16 RT cycles + 3 RT cycles = 163 RT cycles.
192
shows how much a slow received character can be misaligned without causing a noise error
RECEIVER
RT CLOCK
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
MSB
Figure
Figure
Figure 15-8. Slow Data
154 147
------------------------- -
154
–
15-8, the receiver counts 154 RT cycles at the point when
15-8, the receiver counts 170 RT cycles at the point when
×
100
SAMPLES
=
DATA
4.54%
STOP
Freescale Semiconductor