ATMEGA128A-ANR Atmel, ATMEGA128A-ANR Datasheet - Page 228

• Manufacturer Part Number: ATMEGA128A-ANR
• Description: IC MCU AVR 128K FLASH 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA128A-ANR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP
• Core: AVR8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

21.9.3
21.9.4
8151H–AVR–02/11
TWSR - TWI Status Register
TWDR - TWI Data Register
• Bit 1 – Res: Reserved Bit
This bit is a reserved bit and will always read as zero.
• Bit 0 – TWIE: TWI Interrupt Enable
When this bit is written to one, and the I-bit in SREG is set, the TWI interrupt request will be acti-
vated for as long as the TWINT flag is high.
• Bits 7:3 – TWS: TWI Status
These 5 bits reflect the status of the TWI logic and the Two-wire Serial Bus. The different status
codes are described later in this section. Note that the value read from TWSR contains both the
5-bit status value and the 2-bit prescaler value. The application designer should mask the pres-
caler bits to zero when checking the Status bits. This makes status checking independent of
prescaler setting. This approach is used in this datasheet, unless otherwise noted.
• Bit 2 – Res: Reserved Bit
This bit is reserved and will always read as zero.
• Bits 1:0 – TWPS: TWI Prescaler Bits
These bits can be read and written, and control the bit rate prescaler.
Table 21-7.
To calculate bit rates, see
in the equation.
In Transmit mode, TWDR contains the next byte to be transmitted. In receive mode, the TWDR
contains the last byte received. It is writable while the TWI is not in the process of shifting a byte.
This occurs when the TWI interrupt flag (TWINT) is set by hardware. Note that the Data Register
cannot be initialized by the user before the first interrupt occurs. The data in TWDR remains sta-
ble as long as TWINT is set. While data is shifted out, data on the bus is simultaneously shifted
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
TWPS1
0
0
1
1
TWI Bit Rate Prescaler
TWS7
TWD7
R/W
R
7
1
7
1
TWS6
TWD6
R/W
“Bit Rate Generator Unit” on page
R
6
1
6
1
TWS5
TWD5
TWPS0
R/W
R
5
1
5
1
0
1
0
1
TWD4
TWS4
R/W
R
4
1
4
1
Prescaler Value
1
4
16
64
TWD3
TWS3
R/W
R
3
1
3
1
207. The value of TWPS1:0 is used
TWD2
R/W
R
2
–
0
2
1
TWPS1
TWD1
ATmega128A
R/W
R/W
1
0
1
1
TWPS0
TWD0
R/W
R/W
0
1
0
0
TWDR
TWSR
228