ATMEGA128A-ANR Atmel, ATMEGA128A-ANR Datasheet - Page 319

• Manufacturer Part Number: ATMEGA128A-ANR
• Description: IC MCU AVR 128K FLASH 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA128A-ANR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP
• Core: AVR8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

26.9.22
26.9.23
26.9.24
26.9.25
8151H–AVR–02/11
Programming the Lock Bits
Reading the Fuses and Lock Bits
Reading the Signature Bytes
Reading the Calibration Byte
3. Load data byte using programming instructions 6b. A bit value of “0” will program the
4. Write Extended Fuse byte using programming instruction 6c.
5. Poll for Fuse write complete using programming instruction 6d, or wait for t
6. Load data byte using programming instructions 6e. A bit value of “0” will program the
7. Write Fuse high byte using programming instruction 6f.
8. Poll for Fuse write complete using programming instruction 6g, or wait for t
9. Load data byte using programming instructions 6h. A “0” will program the fuse, a “1” will
10. Write Fuse low byte using programming instruction 6i.
11. Poll for Fuse write complete using programming instruction 6j, or wait for t
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Lock bit write using programming instruction 7a.
3. Load data using programming instructions 7b. A bit value of “0” will program the corre-
4. Write Lock bits using programming instruction 7c.
5. Poll for Lock bit write complete using programming instruction 7d, or wait for t
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Fuse/Lock bit read using programming instruction 8a.
3. To read all Fuses and Lock bits, use programming instruction 8f.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Signature byte read using programming instruction 9a.
3. Load address $00 using programming instruction 9b.
4. Read first signature byte using programming instruction 9c.
5. Repeat steps 3 and 4 with address $01 and address $02 to read the second and third
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Calibration byte read using programming instruction 10a.
3. Load address $00 using programming instruction 10b.
4. Read the calibration byte using programming instruction 10c.
corresponding fuse, a “1” will unprogram the fuse.
Table Note: on page
corresponding fuse, a “1” will unprogram the fuse.
Table Note: on page
unprogram the fuse.
Table Note: on page
sponding lock bit, a “1” will leave the lock bit unchanged.
to
To only read Extended Fuse byte, use programming instruction 8b.
To only read Fuse high byte, use programming instruction 8c.
To only read Fuse low byte, use programming instruction 8d.
To only read Lock bits, use programming instruction 8e.
signature bytes, respectively.
Table Note: on page
327).
327).
327).
327).
ATmega128A
WLRH
WLRH
WLRH
WLRH
(refer to
(refer to
(refer to
(refer
319