TMP86xy92DMG Toshiba, TMP86xy92DMG Datasheet - Page 238

• Manufacturer Part Number: TMP86xy92DMG
• Manufacturer: Toshiba

Specifications of TMP86xy92DMG

• Package: SSOP30
• Rom Types (m=mask,p=otp,f=flash): M/F
• Rom Size: 16
• Ram Size: 512
• Driver Led: 8
• Driver Lcd: -
• Spi/sio Channels: 1
• Uart/sio Channels: 2
• I2c/sio Channels: 1
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 6
• Da Converter Channels: -
• Timer Counter 18-bit Channel: -
• Timer Counter 16-bit Channel: 1
• Timer Counter 8-bit Channel: 2
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: -
• Number Of I/o Ports: 24
• Power Supply (v): 4 to 5.5

21.3
DC Characteristics
21.3
Hysteresis voltage
Input current
Input resistance
Output leakage current
Output high voltage
Output low voltage
Output low current
Supply current in
NORMAL1, 2 modes
Supply current in
IDLE 0, 1, 2 modes
Supply current in
SLOW1 mode
Supply current in
SLEEP1 mode
Supply current in
SLEEP0 mode
Supply current in
STOP mode
Peak current of inter-
mittent operation
(Note4,5)
Parameter
Note 1: Typical values show those at Topr = 25 °C and V
Note 2: Input current (I
Note 3: The supply currents of SLOW2 and SLEEP2 modes are equivalent to those of IDLE0, IDLE1 and IDLE2 modes.
Note 4: When a program is executing in the flash memory or when data is being read from the flash memory, the flash memory
Note 5: When designing the power supply, make sure that peak currents can be supplied. In SLOW1 mode, the difference between
DC Characteristics
operates in an intermittent manner, causing peak currents in the operation current, as shown in Figure 21-1.
In this case, the supply current I
peak current and MCU current.
the peak current and the average current becomes large.
Symbol
I
DDP-P
R
R
V
I
V
V
I
I
I
I
I
LO0
IN1
IN2
IN3
OL
DD
HS
IN1
IN2
OH
OL
Hysteresis input
TEST
Sink open drain, tri - state port
RESET
RESET pull - up
PORT pull - up
P0,P1,P2,P3
P0,P1,P2,P3
Except P0
High current port
(P0 Port)
IN3
): The current through pull-up or pull-down resistor is not included.
Pins
DD
(in NORMAL1, NORMAL2 and SLOW1 modes) is defined as the sum of the average
Page 224
V
V
V
V
V
V
V
V
V
V
V
V
V
fc = 16 MHz
fs = 32.768 kHz
V
V
fs = 32.768 kHz
V
V
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
IN
DD
IN
DD
IN
DD
DD
DD
= 5.3 V/0.2 V
= 2.8 V/0.2 V
= 5.3 V/0.2 V
= 5.0V
= 5.5 V, V
= 5.5 V, V
= 5.5 V, V
= 5.5 V, V
= 5.5 V, V
= 4.5 V, I
= 4.5 V, I
= 4.5 V, V
= 5.5 V
= 3.0 V
= 5.5 V
= 5.5 V
= 3.0 V
= 5 V.
OH
OL
IN
IN
IN
IN
OUT
OL
Condition
= 1.6 mA
= 5.5 V/0 V
= 5.5 V
= 0 V
= 0 V
= -0.7 mA
= 1.0 V
= 5.3 V/0.2 V
When a program
operates on flash
memory (Note4,5)
When a program
operates on RAM
When a program
operates on flash
memory (Note4,5)
When a program
operates on RAM
(FLSSTB<FSTB>=
0)
When a program
operates on RAM
(FLSSTB<FSTB>=
1)
Min
100
4.1
50
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
(V
SS
TMP86FH92DMG
Typ.
12.5
= 0 V, Topr = -40 to 85 °C)
200
100
0.9
7.5
5.5
20
22
21
16
14
12
10
10
2
-
-
-
-
Max
450
200
0.4
±2
±2
20
14
65
30
25
22
20
20
9
-
-
-
-
-
Unit
mA
mA
mA
μA
kΩ
kΩ
μA
μA
V
V