C509-L_97 SIEMENS [Siemens Semiconductor Group], C509-L_97 Datasheet - Page 191
C509-L_97
Manufacturer Part Number
C509-L_97
Description
8-Bit CMOS Microcontroller
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.C509-L_97.pdf
(290 pages)
- Current page: 191 of 290
- Download datasheet (5Mb)
On-Chip Peripheral Components
C509-L
Sample Time
:
t S
During this time the internal capacitor array is connected to the selected analog input channel and
is loaded with the analog voltage to be converted. The external analog source needs to be strong
enough to source the current to load the analog input capacitance during the load time. This causes
some restrictions for the impedance of the analog source. The analog voltage is internally fed to a
voltage comparator. With beginning of the sample phase the BSY bit in SFR ADCON0 is set.
Conversion Time t
:
CO
During the conversion time the analog voltage is converted into a 10-bit digital value using the
successive approximation technique with a binary weighted capacitor network. During a conversion
alternating offset and linearity calibration cycles are executed (see also section 6.6.6). At the end
of the conversion phase the BSY bit is reset and the IADC bit in SFR ADCON0 is set indicating a
A/D converter interrupt condition.
Write Result Time t
:
WR
At the result phase the conversion result is written into the ADDATH/ADDATL registers.
Figure 6-50 shows how an A/D conversion is embedded into the microcontroller cycle scheme
using the relation 6 x t
= 1 instruction cycle. It also shows the behaviour of the busy flag (BSY)
IN
and the interrupt flag (IADC) during an A/D conversion.
Depending on the selected prescaler ratios (see figure 6-48), 3 different relationships between
machine cycles and A/D conversion are possible. These 3 relationships are referenced in the
rightmost column of the table in figure 6-49 as a), b), and c).
The single A/D conversion is started when SFR ADDATL is written with dummy data. This write
operation may take one or two machine cycles. In figure 6-50, the instruction MOV ADDATL,#0
starts the A/D conversion (machine cycle X-1 and X). The total A/D conversion (sample, conversion,
and calibration phase) is finished after the end of the n-th machine cycle. In the next machine cycle
n+1 the conversion result is written into the ADDAT registers and can be read in the same cycle by
an instruction (e.g. MOV A,ADDATL). If continuous conversion is selected (bit ADM set), the next
conversion is started with the beginning of the machine cycle which follows the writre result cycle.
The BSY bit is set at the beginning of the first A/D conversion machine cycle and reset at the
beginning of the write result cycle. If continuous conversion is selected, BSY is again set with the
beginning of the machine cycle which follows the write result cycle (n+1).
The interrupt flag IADC is set at the end of the A/D conversion. If the A/D converter interrupt is
enabled and the A/D converter interrupt is priorized to be serviced immediately, the first instruction
of the interrupt service routine will be executed in machine cycle n+4 or n+5. IADC must be reset
by software.
Semiconductor Group
6-113
1997-10-01
Related parts for C509-L_97
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Watts 28volts 200-450
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
50 WATTS - 28VOLTS 200-450 MHZ
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: