C509-L_97 SIEMENS [Siemens Semiconductor Group], C509-L_97 Datasheet - Page 71
C509-L_97
Manufacturer Part Number
C509-L_97
Description
8-Bit CMOS Microcontroller
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.C509-L_97.pdf
(290 pages)
- Current page: 71 of 290
- Download datasheet (5Mb)
Reset / System Clock
C509-L
The time required for a reset operation is the oscillator start-up time plus 2 machine cycles, which,
under normal conditions, must be at least 10 - 20 ms for a crystal oscillator. This requirement is
typically met using a capacitor of 4.7 to 10 F. The same considerations apply if the reset signal is
generated externally (figure 5-1 b). In each case it must be assured that the oscillator has started
up properly and that at least two machine cycles have passed before the reset signal goes inactive.
Figure 5-1
Reset Circuitries
A correct reset leaves the processor in a defined state. The program execution starts at location
0000 H . Depending on the state of the PRGEN pin, either external ROM/EPROM is accessed
(Normal Mode) or the C509-L starts with the bootstrap loader program located in the Boot ROM
(Bootstrap Mode). The default values of the special function registers (SFR) to which they are
forced during reset are listed in table 3-4 and 3-5 of chapter 3.
After reset is internally accomplished the port latches of ports 0 to 6 are set to FF H . This leaves port
0 floating, since it is an open drain port when not used as data/address bus. All other I/O port lines
(ports 1 to 6 and 9) output a one (1). Ports 7 and 8, which are input-only ports, have no internal latch
and therefore the contents of the special function registers P7 and P8 depend on the levels applied
to ports 7 and 8.
The content of the internal RAM of the C509-L is not affected by a reset. After power-up the content
is undefined, while it remains unchanged during a reset it the power supply is not turned off.
Semiconductor Group
5-2
1997-10-01
Related parts for C509-L_97
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Watts 28volts 200-450
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
50 WATTS - 28VOLTS 200-450 MHZ
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: