C509-L_97 SIEMENS [Siemens Semiconductor Group], C509-L_97 Datasheet - Page 72
C509-L_97
Manufacturer Part Number
C509-L_97
Description
8-Bit CMOS Microcontroller
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.C509-L_97.pdf
(290 pages)
- Current page: 72 of 290
- Download datasheet (5Mb)
Reset / System Clock
C509-L
5.2
Hardware Reset Timing
This section describes the timing of the hardware reset signal.
The input pin RESET is sampled once during each machine cycle. This happens in state 5 phase 2.
Thus, the external reset signal is synchronized to the internal CPU timing. When the reset is found
active (low level at pin RESET) the internal reset procedure is started. lt needs two complete
machine cycles to put the complete device to its correct reset state, i.e. all special function registers
contain their default values, the port latches contain 1’s etc. Note that this reset procedure is not
performed if there is no clock available at the device (This can be avoided using the oscillator
watchdog, which provides an auxiliary clock for performing a correct reset without clock at the
XTAL1 and XTAL2 pins). The RESET signal must be active for at least two machine cycles; after
this time the C509-L remains in its reset state as long as the signal is active. When the signal goes
inactive this transition is recognized in the following state 5 phase 2 of the machine cycle. Then the
processor starts its address output (when configured for external ROM) in the following state 5
phase 1. One phase later (state 5 phase 2) the first falling edge at pin ALE occurs.
Figure 5-2 shows this timing for a configuration with EA = 0 (external program memory). Thus,
between the release of the RESET signal and the first falling edge at ALE there is a time period of
at least one machine cycle but less than two machine cycles.
Figure 5-2
CPU Timing after Reset
Semiconductor Group
5-3
1997-10-01
Related parts for C509-L_97
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Watts 28volts 200-450
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
50 WATTS - 28VOLTS 200-450 MHZ
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: