ATMEga64L ATMEL Corporation, ATMEga64L Datasheet - Page 58

no-image

ATMEga64L

Manufacturer Part Number
ATMEga64L
Description
8-bit AVR Microcontroller with 64K Bytes In-System Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEga64L-16AU
Manufacturer:
ROHM
Quantity:
40 000
Part Number:
ATMEga64L-8AC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATMEga64L-8AI
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATMEga64L-8AI
Manufacturer:
ALTERA
0
Part Number:
ATMEga64L-8AI
Manufacturer:
AT
Quantity:
20 000
Part Number:
ATMEga64L-8AJ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATMEga64L-8AQ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATMEga64L-8AQ
Manufacturer:
AT
Quantity:
20 000
Part Number:
ATMEga64L-8AU
Manufacturer:
ATMEL
Quantity:
4 000
Part Number:
ATMEga64L-8AU
Manufacturer:
ATMEL
Quantity:
451
Part Number:
ATMEga64L-8AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATMEga64L-8MI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATMEga64L-8MU
Quantity:
113
Part Number:
ATMEga64L-8MUR
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATMEga64L8AJ
Manufacturer:
ATMEL
Quantity:
6 973
Timed Sequences for
Changing the
Configuration of the
Watchdog Timer
Safety Level 0
Safety Level 1
Safety Level 2
58
ATmega64(L)
The sequence for changing configuration differs slightly between the three safety levels.
Separate procedures are described for each level.
This mode is compatible with the Watchdog operation found in ATmega103. The Watch-
dog Timer is initially disabled, but can be enabled by writing the WDE bit to 1 without
any restriction. The Time-out period can be changed at any time without restriction. To
disable an enabled Watchdog Timer, the procedure described on page 56 (WDE bit
description) must be followed.
In this mode, the Watchdog Timer is initially disabled, but can be enabled by writing the
WDE bit to 1 without any restriction. A timed sequence is needed when changing the
Watchdog Time-out period or disabling an enabled Watchdog Timer. To disable an
enabled Watchdog Timer, and/or changing the Watchdog Time-out, the following proce-
dure must be followed:
1. In the same operation, write a logic one to WDCE and WDE. A logic one must be
2. Within the next four clock cycles, in the same operation, write the WDE and WDP
In this mode, the Watchdog Timer is always enabled, and the WDE bit will always read
as one. A timed sequence is needed when changing the Watchdog Time-out period. To
change the Watchdog Time-out, the following procedure must be followed:
1. In the same operation, write a logical one to WDCE and WDE. Even though the
2. Within the next four clock cycles, in the same operation, write the WDP bits as
written to WDE regardless of the previous value of the WDE bit.
bits as desired, but with the WDCE bit cleared.
WDE always is set, the WDE must be written to one to start the timed sequence.
desired, but with the WDCE bit cleared. The value written to the WDE bit is
irrelevant.
2490G–AVR–03/04

Related parts for ATMEga64L