AT86RF212-ZU Atmel, AT86RF212-ZU Datasheet - Page 41

• Manufacturer Part Number: AT86RF212-ZU
• Description: IC TXRX ZIGBE/802.15.4/ISM 32QFN
• Manufacturer: Atmel

Specifications of AT86RF212-ZU

• Frequency: 700MHz, 800MHz, 900MHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, ISM
• Applications: ISM, ZigBee™
• Power - Output: 10dBm
• Sensitivity: -110dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 9.2mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 769 MHz to 935 MHz
• Interface Type: SPI
• Noise Figure: 7 dB
• Output Power: 21 dB
• Operating Supply Voltage: 1.8 V, 3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 25 mA
• Minimum Operating Temperature: - 40 C
• Modulation: OQPSK
• Protocol Supported: 802.15.4
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8168C-MCU Wireless-02/10
Register 0x02 (TRX_STATE):
Radio transceiver state changes can be initiated by writing register bits TRX_CMD. This
register is used for Basic and Extended Operating Mode, refer to section 5.2.
Table 5-5. Register 0x02 (TRX_STATE)
• Bit 7:5 – TRAC_STATUS
Refer to section 5.2.6.
• Bit 4:0 – TRX_CMD
A write access to register bits TRX_CMD initiates a radio transceiver state transition.
Table 5-6. State Control Command, Register Bits TRX_CMD
Bit
Name
Read/Write
Reset Value
Bit
Name
Read/Write
Reset Value
Notes:
Register Bits
TRX_CMD
Notes:
1. Extended Operating Mode only, refer to section 5.2.6.
2. Do not try to initiate a further state change while the radio transceiver is in
3. Register is not accessible in SLEEP state.
1. FORCE_PLL_ON is not valid for states SLEEP, P_ON, RESET, and all *_NOCLK
2. Extended Operating Mode only, refer to section 5.2.6.
states, as well as STATE_TRANSITION_IN_PROGRESS towards these states.
STATE_TRANSITION_IN_PROGRESS state.
7
TRAC_STATUS
R
0
3
TRX_CMD[3]
R/W
0
Value
0x00
0x02
0x03
0x04
0x06
0x08
0x09
0x16
0x19
(1)
(2)
(2)
6
TRAC_STATUS
R
0
2
TRX_CMD[2]
R/W
0
State Transition towards
NOP
TX_START
FORCE_TRX_OFF
FORCE_PLL_ON
RX_ON
TRX_OFF (CLK Mode)
PLL_ON (TX_ON)
RX_AACK_ON
TX_ARET_ON
All other values are reserved and mapped to NOP.
5
TRAC_STATUS
R
0
1
TRX_CMD[1]
R/W
0
AT86RF212
4
TRX_CMD[4]
R/W
0
0
TRX_CMD[0]
R/W
0
41