AT86RF212-ZU Atmel, AT86RF212-ZU Datasheet - Page 49

• Manufacturer Part Number: AT86RF212-ZU
• Description: IC TXRX ZIGBE/802.15.4/ISM 32QFN
• Manufacturer: Atmel

Specifications of AT86RF212-ZU

• Frequency: 700MHz, 800MHz, 900MHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, ISM
• Applications: ISM, ZigBee™
• Power - Output: 10dBm
• Sensitivity: -110dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 9.2mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 769 MHz to 935 MHz
• Interface Type: SPI
• Noise Figure: 7 dB
• Output Power: 21 dB
• Operating Supply Voltage: 1.8 V, 3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 25 mA
• Minimum Operating Temperature: - 40 C
• Modulation: OQPSK
• Protocol Supported: 802.15.4
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8168C-MCU Wireless-02/10
Table 5-9. Configuration of IEEE 802.15.4 Devices
Notes
• The default value of the short address is 0xFFFF. Thus, if no short address has been
• In the IEEE 802.15.4-2003 standard the frame version subfield does not yet exist but
PAN Coordinator
Table 5-10 shows the RX_AACK configuration registers required to setup a PAN
coordinator device.
0x20,0x21
0x22,0x23
Register
Address
configured, only frames with either the broadcast address or the IEEE address are
accepted by the frame filter.
is marked as reserved. According to this standard, reserved fields have to be set to
zero. At the same time, the IEEE 802.15.4-2003 standard requires ignoring reserved
bits upon reception. Thus, there is a contradiction in the standard which can be
interpreted in two ways:
1. If a network should only allow access to nodes compliant to IEEE 802.15.4-2003,
2. If a device should acknowledge all frames independent of its frame version,
The same holds for PAN coordinators, see below.
0x0C
0x2C
0x2B
0x2E
0x24
then AACK_FVN_MODE should be set to 0.
AACK_FVN_MODE should be set to 3. However, this may result in conflicts with
co-existing IEEE 802.15.4-2006 standard compliant networks.
…
Register
7:6
Bit
7
0
Name
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
…
IEEE_ADDR_7
RX_SAFE_MODE
SLOTTED_OPERATION
AACK_FVN_MODE
Description
Setup Frame Filter, see section 6.2.1
0: Disable frame protection
1: Enable frame protection
0: Transceiver operates in unslotted
mode.
1: Transceiver operates in slotted mode,
see section 5.2.3.5
Controls the ACK behavior, depending on
FCF frame version number
b00: Acknowledges only frames with
version number 0, i.e. according to
IEEE 802.15.4-2003 frames
b01: Acknowledges only frames with
version number 0 or 1, i.e. frames
according to IEEE 802.15.4-2003/2006
b10: Acknowledges only frames with
version number 0 or 1 or 2
b11: Acknowledges all frames
independent of the FCF frame version
number
AT86RF212
49