AT86RF212-ZU Atmel, AT86RF212-ZU Datasheet - Page 83

IC TXRX ZIGBE/802.15.4/ISM 32QFN

AT86RF212-ZU

Manufacturer Part Number
AT86RF212-ZU
Description
IC TXRX ZIGBE/802.15.4/ISM 32QFN
Manufacturer
Atmel
Datasheet

Specifications of AT86RF212-ZU

Frequency
700MHz, 800MHz, 900MHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4 Zigbee, 6LoWPAN, ISM
Applications
ISM, ZigBee™
Power - Output
10dBm
Sensitivity
-110dBm
Voltage - Supply
1.8 V ~ 3.6 V
Current - Receiving
9.2mA
Current - Transmitting
25mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
Number Of Receivers
1
Number Of Transmitters
1
Wireless Frequency
769 MHz to 935 MHz
Interface Type
SPI
Noise Figure
7 dB
Output Power
21 dB
Operating Supply Voltage
1.8 V, 3 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Maximum Supply Current
25 mA
Minimum Operating Temperature
- 40 C
Modulation
OQPSK
Protocol Supported
802.15.4
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT86RF212-ZU
Manufacturer:
HITTITE
Quantity:
5 000
Part Number:
AT86RF212-ZU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT86RF212-ZUR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
6.5.3 Data Interpretation
6.5.4 Interrupt Handling
6.5.5 Register Description
8168C-MCU Wireless-02/10
The PHY_ED_LEVEL (ED) is an 8-bit register. The ED value of the AT86RF212 has a
valid range from 0x00 to 0x54 (0 to 84) with a resolution of about 1 dB. Values 0x55 to
0xFE do not occur and a value of 0xFF indicates the reset value.
An ED value of 0 indicates a receiver input power less than or equal to
RSSI_BASE_VAL [dBm] (refer to Table 6-25); a value of 85 indicates an input power
equal to or larger than (RSSI_BASE_VAL + 87) [dBm].
The receiver input power can be calculated as follows:
Figure 6-4. Mapping between ED Value and Receiver Input Power
Interrupt IRQ_4 (CCA_ED_DONE) is issued at the end of a manually initiated ED
measurement.
Note that an ED measurement should only be initiated in RX states but not in
RX_AACK
(CCA_ED_DONE) without actually performing an ED measurement.
Register 0x07 (PHY_ED_LEVEL)
The PHY_ED_LEVEL register contains the result of an ED measurement.
90
80
70
60
50
40
30
20
10
0
-100
P
RF
[dBm] = RSSI_BASE_VAL + 1.03 ⋅ ED_LEVEL
states.
Otherwise,
-80
Receiver Input Power [dBm]
the
-60
radio
transceiver
-40
BPSK with 300 kchip/s
BPSK with 600 kchip/s
O-QPSK with 400 kchip/s
O-QPSK with 1000 kchip/s (SIN)
generates
AT86RF212
-20
an
IRQ_4
0
83

Related parts for AT86RF212-ZU