ATmega16U2 Atmel Corporation, ATmega16U2 Datasheet - Page 189
ATmega16U2
Manufacturer Part Number
ATmega16U2
Description
Manufacturer
Atmel Corporation
Specifications of ATmega16U2
Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
22
Ext Interrupts
21
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
5
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA16U2
Manufacturer:
ATMEL
Quantity:
853
Company:
Part Number:
ATmega16U2-MU
Manufacturer:
RALINK
Quantity:
2 400
- Current page: 189 of 309
- Download datasheet (6Mb)
20.3.3
20.4
20.4.1
20.4.2
7799D–AVR–11/10
General Operating Modes
Design guidelines
Introduction
Power-on and reset
The following design guidelines should be met:
In addition it is highly recommended to connect a 10µF capacitor to the VBUS line
The USB controller is disabled and reset after a hardware reset generated by:
In the case of USB End Of Reset (EOR), the USB controller is reset, but not disabled. Therefore
the device remains attached.
Figure 20-7 on page 189
Figure 20-7. USB controller states after reset
• Serial resistors on USB Data lines must have 22 Ohms value (
• Traces from the input USB receptacle (or from the cable connection in the case of a tethered
• Voltage transient / ESD suppressors may also be used to prevent USB pads to be damaged
• U
device) to the USB microcontroller pads should be as short as possible, and follow differential
traces routing rules (same length, as near as possible and avoid vias accumulation).
by external disturbances.
cap
– Power on reset
– External reset
– Watchdog reset
– Brown out reset
– debugWIRE reset
– USB End Of Reset
capacitor should be 1µF (
Clock stopped
FRZCLK = 1
(macro off)
USBE = 1
Device
illustrates the USB controller main states on power-on:
+/-
10%) for correct operation.
USBE = 0
Reset
HW RESET
(from EOR)
ATmega8U2/16U2/32U2
USBE = 0
USBE = 0
+/-
(except from EOR)
Any other
5%).
HW RESET
state
189
Related parts for ATmega16U2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: