ATmega16U2 Atmel Corporation, ATmega16U2 Datasheet - Page 247

• Manufacturer Part Number: ATmega16U2
• Manufacturer: Atmel Corporation

Specifications of ATmega16U2

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 22
• Ext Interrupts: 21
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 5
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

25.2
7799D–AVR–11/10
Fuse Bits
Table 25-2.
Notes:
The ATmega8U2/16U2/32U2 has three Fuse bytes.
functionality of all the fuses and how they are mapped into the Fuse bytes. Note that the fuses
are read as logical zero, “0”, if they are programmed.
Table 25-3.
Note:
–
–
–
–
HWBE
BODLEVEL2
BODLEVEL1
BODLEVEL0
BLB1 Mode
Fuse Low Byte
1
2
3
4
1. Program the Fuse bits and Boot Lock bits before programming the LB1 and LB2.
2. “1” means unprogrammed, “0” means programmed
1. See
Memory Lock Bits
(1)
(1)
(1)
Lock Bit Protection Modes
Extended Fuse Byte
“System and Reset Characteristics” on page 267
BLB12
1
1
0
0
7
6
5
4
3
2
1
0
Bit No
BLB11
1
0
0
1
Description
–
–
–
–
Hardware Boot Enable
Brown-out Detector trigger level
Brown-out Detector trigger level
Brown-out Detector trigger level
Protection Type
No restrictions for SPM or (E)LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
(1)(2)
(Continued)
ATmega8U2/16U2/32U2
Table 25-3
for BODLEVEL Fuse decoding.
-
Table 25-5
Default Value : 0xF4
1
1
1
1
0 (programmed)
1 (unprogrammed)
0 (programmed)
0 (programmed)
describe briefly the
247