ATmega16U2 Atmel Corporation, ATmega16U2 Datasheet - Page 299

• Manufacturer Part Number: ATmega16U2
• Manufacturer: Atmel Corporation

Specifications of ATmega16U2

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 22
• Ext Interrupts: 21
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 5
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

32. Errata
32.1
32.1.1
32.2
32.2.1
32.3
32.3.1
7799D–AVR–11/10
Errata ATmega8U2
Errata ATmega16U2
Errata ATmega32U2
rev. A and rev B
rev. A and rev B
rev. C
The revision letter in this section refers to the revision of the ATmega8U2 device.
• Full Swing oscillator
1. Full Swing oscillator
The revision letter in this section refers to the revision of the ATmega16U2 device.
• Full Swing oscillator
1. Full Swing oscillator
The revision letter in this section refers to the revision of the ATmega32U2 device.
No Known Errata
The maximum frequency for the Full Swing Crystal Oscillator is 8MHz. For Crystal frequen-
cies > 8MHz the Full Swing Crystal Oscillator is not guaranteed to operate correctly.
Problem fix/Workaround
If a Crystal with frequency > 8MHz is used, the Low Power Crystal Oscillator option should
be used instead. See table 8-1 for an overview of the Device Clocking Options. Note that the
Low Power Crystal Oscillator will not provide full rail-to-rail swing on the XTAL2 pin. If sys-
tem clock output is needed to drive other clock inputs while running from the Low Power
Crystal Oscillator, the system clock can be output on PORTC7 by programming the CKOUT
fuse.
The maximum frequency for the Full Swing Crystal Oscillator is 8MHz. For Crystal frequen-
cies > 8MHz the Full Swing Crystal Oscillator is not guaranteed to operate correctly.
Problem fix/Workaround
If a Crystal with frequency > 8MHz is used, the Low Power Crystal Oscillator option should
be used instead. See table 8-1 for an overview of the Device Clocking Options. Note that the
Low Power Crystal Oscillator will not provide full rail-to-rail swing on the XTAL2 pin. If sys-
tem clock output is needed to drive other clock inputs while running from the Low Power
Crystal Oscillator, the system clock can be output on PORTC7 by programming the CKOUT
fuse.
ATmega8U2/16U2/32U2
299