SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 165

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

21.5.2
Name:
Address:
Access:
• SLOT_CYCLE: Maximum Number of Allowed Cycles for a Burst
When the SLOT_CYCLE limit is reach for a burst it may be broken by another master trying to access this slave.
This limit has been placed to avoid locking very slow slave by when very long burst are used.
This limit should not be very small though. Unreasonable small value will break every burst and Bus Matrix will spend its
time to arbitrate without performing any data transfer. 16 cycles is a reasonable value for SLOT_CYCLE.
• DEFMASTR_TYPE: Default Master Type
0: No Default Master
At the end of current slave access, if no other master request is pending, the slave is disconnected from all masters.
This results in having a one cycle latency for the first access of a burst transfer or for a single access.
1: Last Default Master
At the end of current slave access, if no other master request is pending, the slave stay connected with the last master hav-
ing accessed it.
This results in not having the one cycle latency when the last master re-tries access on the slave again.
2: Fixed Default Master
At the end of the current slave access, if no other master request is pending, the slave connects to the fixed master which
number has been written in the FIXED_DEFMSTR field.
This results in not having the one cycle latency when the fixed master re-tries access on the slave again.
• FIXED_DEFMSTR: Fixed Default Master
This is the number of the Default Master for this slave. Only used if DEFMASTR_TYPE is 2. Specifying the number of a
master which is not connected to the selected slave is equivalent to setting DEFMASTR_TYPE to 0.
• ARBT: Arbitration Type
0: Round-Robin Arbitration
1: Fixed Priority Arbitration
2: Reserved
3: Reserved
6254C–ATARM–22-Jan-10
31
23
15
–
–
–
7
Bus Matrix Slave Configuration Registers
MATRIX_SCFG0...MATRIX_SCFG4
0xFFFFEE40
Read-write
30
22
14
–
–
6
29
21
13
–
–
5
AT91SAM9XE128/256/512 Preliminary
28
20
12
–
–
4
SLOT_CYCLE
FIXED_DEFMSTR
27
19
11
–
–
3
26
18
10
–
–
2
25
17
9
–
1
DEFMSTR_TYPE
ARBT
24
16
8
–
0
165