SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 199

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

23.7.2.1
23.7.2.2
6254C–ATARM–22-Jan-10
Byte Write Access
Byte Select Access
Byte write access supports one byte write signal per byte of the data bus and a single read
signal.
Note that the SMC does not allow boot in Byte Write Access mode.
In this mode, read/write operations can be enabled/disabled at a byte level. One byte-select line
per byte of the data bus is provided. One NRD and one NWE signal control read and write.
Figure 23-7
mode, on NCS3 (BAT = Byte Select Access).
• For 16-bit devices: the SMC provides NWR0 and NWR1 write signals for respectively byte0
• For 32-bit devices: NWR0, NWR1, NWR2 and NWR3, are the write signals of byte0 (lower
• For 16-bit devices: the SMC provides NBS0 and NBS1 selection signals for respectively
• For 32-bit devices: NBS0, NBS1, NBS2 and NBS3, are the selection signals of byte0 (lower
(lower byte) and byte1 (upper byte) of a 16-bit bus. One single read signal (NRD) is provided.
byte), byte1, byte2 and byte 3 (upper byte) respectively. One single read signal (NRD) is
provided.
byte0 (lower byte) and byte1 (upper byte) of a 16-bit bus.
byte), byte1, byte2 and byte 3 (upper byte) respectively. Byte Select Access is used to
connect two 16-bit devices.
Byte Write Access is used to connect 2 x 8-bit devices as a 16-bit memory.
Byte Write Access is used to connect 4 x 8-bit devices as a 32-bit memory.
Byte Write option is illustrated on
Byte Select Access is used to connect one 16-bit device.
shows how to connect two 16-bit devices on a 32-bit data bus in Byte Select Access
AT91SAM9XE128/256/512 Preliminary
Figure
23-6.
199