SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 85
SAM9XE512
Manufacturer Part Number
SAM9XE512
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9260.pdf
(290 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9XE128.pdf
(860 pages)
4.SAM9XE128.pdf
(48 pages)
Specifications of SAM9XE512
Flash (kbytes)
512 Kbytes
Pin Count
217
Max. Operating Frequency
180 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
6
Ssc
1
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
Yes
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
312
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.65 to 1.95
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- SAM9260 PDF datasheet
- SAM9261 PDF datasheet #2
- SAM9XE128 PDF datasheet #3
- SAM9XE128 PDF datasheet #4
- Current page: 85 of 860
- Download datasheet (13Mb)
14. Fast Flash Programming Interface (FFPI)
14.1
14.2
14.2.1
Table 14-1.
6254C–ATARM–22-Jan-10
Signal Name
VDDBU
VDDIO
VDDCORE
VDDPLL
GND
Description
Parallel Fast Flash Programming
Device Configuration
Signal Description List
Function
Backup Power Supply
I/O Lines Power Supply
Core Power Supply
PLL Power Supply
Ground
The Fast Flash Programming Interface provides two solutions - parallel or serial - for high-vol-
ume programming using a standard gang programmer. The parallel interface is fully
handshaked and the device is considered to be a standard EEPROM. Additionally, the parallel
protocol offers an optimized access to all the embedded Flash functionalities. The serial inter-
face uses the standard IEEE 1149.1 JTAG protocol. It offers an optimized access to all the
embedded Flash functionalities.
Although the Fast Flash Programming Mode is a dedicated mode for high volume programming,
this mode not designed for in-situ programming.
In Fast Flash Programming Mode, the device is in a specific test mode. Only a certain set of pins
is significant. Other pins must be left unconnected.
Figure 14-1. Parallel Programming Interface
MODE[3:0]
DATA[15:0]
0 - 50MHz
VDDBU
NVALID
VDDIO
VDDIO
NCMD
AT91SAM9XE128/256/512 Preliminary
GND
GND
NOE
RDY
Power
PGMD[15:0]
PGMEN3
TST
PGMEN0
PGMEN1
PGMEN2
PGMNCMD
PGMRDY
PGMNOE
PGMNVALID
PGMM[3:0]
XIN
Ground
Power
Power
Power
Type
Active
Level
Comments
VDDCORE
VDDIO
VDDPLL
GND
85
Related parts for SAM9XE512
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: