SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 474

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

33.9.5.7
33.9.5.8
Figure 33-30. Repeated Start + Reversal from Read to Write Mode
33.9.5.9
Figure 33-31. Repeated Start + Reversal from Write to Read Mode
Notes:
474
TWI_RHR
TWI_RHR
TWI_THR
TWI_THR
TXCOMP
TXCOMP
EOSACC
EOSACC
SVREAD
SVREAD
RXRDY
SVACC
RXRDY
SVACC
TXRDY
TXRDY
TWD
TWD
1. In this case, if TWI_THR has not been written at the end of the read command, the clock is automatically stretched before
2. TXCOMP is only set at the end of the transmission because after the repeated start, SADR is detected again.
AT91SAM9XE128/256/512 Preliminary
the ACK.
Reversal after a Repeated Start
Reversal of Read to Write
Reversal of Write to Read
S
S
As soon as a START is detected
As soon as a START is detected
SADR
SADR
The master initiates the communication by a read command and finishes it by a write command.
Figure 33-30 on page 474
1. TXCOMP is only set at the end of the transmission because after the repeated start, SADR is detected again.
The master initiates the communication by a write command and finishes it by a read com-
mand.Figure 33-31 on page 474
mode.
W
R
Read TWI_RHR
A
A
DATA0
DATA0
DATA0
A
A
DATA0
DATA1
DATA1
DATA1
describes the repeated start + reversal from Read to Write mode.
NA
A
describes the repeated start + reversal from Write to Read
DATA1
Sr
Sr
SADR
SADR
Cleared after read
Cleared after read
R
W
DATA2
A
A
DATA2
DATA2
DATA2
A
A
DATA3
DATA3
DATA3
6254C–ATARM–22-Jan-10
DATA3
NA
A
P
P