SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 681

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

38.5.4
Register Name:
Address:
Access Type:
This register, when read, provides details of the status of a transmit. Once read, individual bits may be cleared by writing 1
to them. It is not possible to set a bit to 1 by writing to the register.
• UBR: Used Bit Read
Set when a transmit buffer descriptor is read with its used bit set. Cleared by writing a one to this bit.
• COL: Collision Occurred
Set by the assertion of collision. Cleared by writing a one to this bit.
• RLE: Retry Limit exceeded
Cleared by writing a one to this bit.
• TGO: Transmit Go
If high transmit is active.
• BEX:
If the buffers run out during transmission of a frame, then transmission stops, FCS shall be bad and tx_er asserted. Cleared
by writing a one to this bit.
• COMP: Transmit Complete
Set when a frame has been transmitted. Cleared by writing a one to this bit.
• UND: Transmit Underrun
Set when transmit DMA was not able to read data from memory, either because the bus was not granted in time, because
a not OK hresp(bus error) was returned or because a used bit was read midway through frame transmission. If this
occurs, the transmitter forces bad CRC. Cleared by writing a one to this bit.
6254C–ATARM–22-Jan-10
31
23
15
–
–
–
7
–
Buffers exhausted mid frame
Transmit Status Register
UND
30
22
14
EMAC_TSR
0xFFFC4014
Read-write
–
–
–
6
COMP
29
21
13
–
–
–
5
AT91SAM9XE128/256/512 Preliminary
BEX
28
20
12
–
–
–
4
TGO
27
19
11
–
–
–
3
RLE
26
18
10
–
–
–
2
COL
25
17
–
–
9
–
1
UBR
24
16
–
–
8
–
0
681