SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 678

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

38.5.2
Register Name:
Address:
Access Type:
• SPD: Speed
Set to 1 to indicate 100 Mbit/s operation, 0 for 10 Mbit/s. The value of this pin is reflected on the speed pin.
• FD: Full Duplex
If set to 1, the transmit block ignores the state of collision and carrier sense and allows receive while transmitting. Also con-
trols the half_duplex pin.
• CAF: Copy All Frames
When set to 1, all valid frames are received.
• JFRAME: Jumbo Frames
Set to one to enable jumbo frames of up to 10240 bytes to be accepted.
• NBC: No Broadcast
When set to 1, frames addressed to the broadcast address of all ones are not received.
• MTI: Multicast Hash Enable
When set, multicast frames are received when the 6-bit hash function of the destination address points to a bit that is set in
the hash register.
• UNI: Unicast Hash Enable
When set, unicast frames are received when the 6-bit hash function of the destination address points to a bit that is set in
the hash register.
• BIG: Receive 1536 Bytes Frames
Setting this bit means the EMAC receives frames up to 1536 bytes in length. Normally, the EMAC would reject any frame
above 1518 bytes.
• CLK: MDC Clock Divider
Set according to system clock speed. This determines by what number system clock is divided to generate MDC. For con-
formance with 802.3, MDC must not exceed 2.5MHz (MDC is only active during MDIO read and write operations).
678
UNI
31
23
15
–
–
7
AT91SAM9XE128/256/512 Preliminary
Network Configuration Register
RBOF
MTI
30
22
14
EMAC_NCFG
0xFFFC4004
Read-write
–
–
6
NBC
PAE
29
21
13
–
–
5
RTY
CAF
28
20
12
–
–
4
JFRAME
IRXFCS
27
19
11
–
3
CLK
EFRHD
26
18
10
–
2
–
DRFCS
FD
25
17
–
9
–
1
6254C–ATARM–22-Jan-10
RLCE
SPD
BIG
24
16
–
8
0