SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 458

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

33.7.7
33.7.7.1
33.7.7.2
33.7.8
33.7.9
458
AT91SAM9XE128/256/512 Preliminary
Using the Peripheral DMA Controller (PDC)
SMBUS Quick Command (Master Mode Only)
Read-write Flowcharts
Data Transmit with the PDC
Data Receive with the PDC
The use of the PDC significantly reduces the CPU load.
To assure correct implementation, respect the following programming sequences:
The TWI interface can perform a Quick Command:
Figure 33-14. SMBUS Quick Command
The following flowcharts shown in
33-18 on page
read and write operations. A polling or interrupt method can be used to check the status bits.
The interrupt method requires that the interrupt enable register (TWI_IER) be configured first.
1. Initialize the transmit PDC (memory pointers, size, etc.).
2. Configure the master mode (DADR, CKDIV, etc.).
3. Start the transfer by setting the PDC TXTEN bit.
4. Wait for the PDC end TX flag.
5. Disable the PDC by setting the PDC TXDIS bit.
1. Initialize the receive PDC (memory pointers, size - 1, etc.).
2. Configure the master mode (DADR, CKDIV, etc.).
3. Start the transfer by setting the PDC RXTEN bit.
4. Wait for the PDC end RX flag.
5. Disable the PDC by setting the PDC RXDIS bit.
1. Configure the master mode (DADR, CKDIV, etc.).
2. Write the MREAD bit in the TWI_MMR register at the value of the one-bit command to
3. Start the transfer by setting the QUICK bit in the TWI_CR.
be sent.
462,
Figure 33-19 on page 463
TXCOMP
Write QUICK command in TWI_CR
TXRDY
TWD
Figure 33-16 on page
S
DADR
and
Figure 33-20 on page 464
R/W
460,
A
Figure 33-17 on page
P
6254C–ATARM–22-Jan-10
give examples for
461,
Figure