SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 719

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 39-11. Data OUT Transfer for Ping-pong Endpoint
Note:
39.5.2.8
719
USB Bus
Packets
RX_DATA_BK0 Flag
(UDP_CSRx)
RX_DATA_BK1 Flag
(UDP_CSRx)
FIFO (DPR)
Bank 0
FIFO (DPR)
Bank 1
An interrupt is pending while the RX_DATA_BK0 or RX_DATA_BK1 flag is set.
AT91SAM9XE128/256/512 Preliminary
Stall Handshake
Host Sends First Data Payload
Data OUT
PID
Set by USB Device,
Data Payload Written
in FIFO Endpoint Bank 0
Write by USB Device
Data OUT1
Warning: When RX_DATA_BK0 and RX_DATA_BK1 are both set, there is no way to determine
which one to clear first. Thus the software must keep an internal counter to be sure to clear alter-
natively RX_DATA_BK0 then RX_DATA_BK1. This situation may occur when the software
application is busy elsewhere and the two banks are filled by the USB host. Once the application
comes back to the USB driver, the two flags are set.
A stall handshake can be used in one of two distinct occasions. (For more information on the
stall handshake, refer to Chapter 8 of the Universal Serial Bus Specification, Rev 2.0.)
The following procedure generates a stall packet:
10. The microcontroller transfers out data received from the endpoint’s memory to the
11. The microcontroller notifies the USB device it has finished the transfer by clearing
12. A fourth Data OUT packet can be accepted by the USB device and copied in the FIFO
• A functional stall is used when the halt feature associated with the endpoint is set. (Refer to
• To abort the current request, a protocol stall is used, but uniquely with control transfer.
Chapter 9 of the Universal Serial Bus Specification, Rev 2.0, for more information on the halt
feature.)
microcontroller’s memory. Data received is available by reading the endpoint’s
UDP_FDRx register.
RX_DATA_BK1 in the endpoint’s UDP_CSRx register.
Bank 0.
Data OUT 1
ACK
PID
Read By Microcontroller
Set by USB Device,
Data Payload Written
in FIFO Endpoint Bank 1
Interrupt Pending
Microcontroller Reads Data 1 in Bank 0,
Host Sends Second Data Payload
Data OUT 1
Data OUT
PID
Write by USB Device
Data OUT 2
Data OUT 2
Cleared by Firmware
ACK
PID
Read By Microcontroller
Data OUT
Microcontroller Reads Data2 in Bank 1,
Host Sends Third Data Payload
PID
Interrupt Pending
Data OUT 2
Write In Progress
Cleared by Firmware
Data OUT 3
6254C–ATARM–22-Jan-10
Data OUT 3
A
P