DS3184DK Maxim Integrated Products, DS3184DK Datasheet - Page 143
DS3184DK
Manufacturer Part Number
DS3184DK
Description
KIT DEMO FOR DS3184
Manufacturer
Maxim Integrated Products
Datasheet
1.DS3184DK.pdf
(400 pages)
Specifications of DS3184DK
Main Purpose
Telecom, ATM / Packet PHYs
Utilized Ic / Part
DS3184
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Secondary Attributes
-
Embedded
-
Primary Attributes
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 143 of 400
- Download datasheet (4Mb)
DS3181/DS3182/DS3183/DS3184
Figure 10-26. Receive DSS Scrambler Synchronization State Diagram
Steady
State
8 Cells Fail Verification
Verification
Acquisition
32 Samples Loaded
If cell processing is disabled, a cell boundary is arbitrarily chosen, and the data is divided into "cells" whose size is
programmable. If HEC transfer is enabled in the receive system interface, the incoming data stream will be divided
into 53-byte "cells". If HEC transfer is disabled in the receive system interface, the data is divided into 52-byte
"cells". These cells are then passed on to bit reordering bypassing cell delineation, OCD detection, cell filtering,
header pattern comparison, HEC error monitoring, and HEC byte filtering.
Cell delineation determines the cell boundary by identifying the header bytes and the HEC byte of a cell, and
detects an out of cell delineation (OCD) condition or a change of cell delineation (COCD). Cell delineation is
performed off-line, and the data path cell boundary is only updated by cell delineation if an OCD condition is
present. Performing cell delineation off-line results in fewer cells being discarded when the cell boundary changes.
If DSS scrambling is enabled (bit synchronous mode only), only the six least significant bits (LSBs) of the HEC
(HEC[3:8]) are used for cell delineation, as the two most significant bits (MSBs) are scrambled. An OCD condition
is declared if seven consecutive cells are received with incorrect HEC bytes. An OCD condition is terminated if
“Delta” consecutive cells are received with correct HEC bytes, if cell delineation updates the data path cell
boundary, or if the PLCP framer updates the data path cell boundary (PLCP modes only). All ATM cells are
discarded during an OCD condition. A COCD is declared when Cell Delineation or the PLCP framer updates the
data path cell boundary with a cell boundary that is different from the current data path cell boundary .
Cell delineation has three states: "Hunt", "Presync", and "Sync". The "Hunt" state searches for the cell boundary.
Each time slot is checked for an HEC byte (six LSBs of the HEC byte if DSS is enabled). The cell boundary is set
once the header and HEC bytes are identified, and cell delineation transitions to the “Presync” state. The "Presync"
state verifies the cell boundary identified in the “Hunt” state. The HEC is checked in each incoming cell. If “Delta”
cells (including the "Hunt" to "Presync" transition cell) with a correct HEC are received, cell delineation transitions
to the “Sync” state. If a cell with an incorrect HEC is received, cell delineation transitions to the “Hunt” state. The
"Sync" state checks the HEC in each cell. If a cell with a correct HEC is received, cell delineation updates the data
path cell boundary if an OCD condition is present. If a cell with an incorrect HEC is received, cell delineation
transitions to the “Hunt” state. The cell delineation state diagram is shown in
Figure
10-27. The cell delineation
process starts in the "Hunt" state. In octet-aligned mode, the HEC check is performed one byte at a time, so up to
53 checks may be needed to find the cell boundary. In bit synchronous mode, the HEC check is performed one bit
at a time, so up to 424 checks may be needed to find the cell boundary. HEC calculation coset polynomial addition
can be disabled. The cell delineation process can be programmed to ignore the first header byte (for DQDB
applications) when calculating the HEC. If cell processing is disabled, cell delineation will not be performed. A
“Delta” of eight is used during the DS3 clear-channel, STS-1 clear-channel, and E3 clear-channel modes. A “Delta”
143
Related parts for DS3184DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC QUAD ATM/PACKET PHY 400-PBGA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
IC PACKET PHY W/LIU 400-CSBGA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products