CY8CTST200-24LQXI Cypress Semiconductor Corp, CY8CTST200-24LQXI Datasheet - Page 88

• Manufacturer Part Number: CY8CTST200-24LQXI
• Description: IC MCU 32K FLASH 24UQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: TrueTouch™r

Specifications of CY8CTST200-24LQXI

• Program Memory Type: FLASH (32 kB)
• Package / Case: 24-WQFN Exposed Pad, 24-HWQFN
• Applications: Touchscreen Controller
• Core Processor: M8C
• Controller Series: CY8CT
• Ram Size: 2K x 8
• Interface: I²C, SPI, UART/USART, USB
• Number Of I /o: 20
• Voltage - Supply: 1.8 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Processor Series: CY8CTxx2xx
• Core: M8C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Timers: 3
• Operating Supply Voltage: 1.71 V to 5.5 V
• Mounting Style: SMD/SMT
• Program Memory Size: 32 KB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1000 - ISP 4PORT FOR CYPRESS PSOC MCU
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-2956

For typical capacitances, the IDAC current can be config-
ured so that the average voltage on the analog global does
not change. This can be done in firmware using a succes-
sive approximation to find the IDAC setting that causes the
global net to remain relatively stable for the load capaci-
tance. After this baseline is set, a small increase in sense
capacitance causes the global net to slowly discharge,
eventually crossing the comparator threshold. The config-
urable low pass filter is designed to filter the ripple on the
global net, leaving the average voltage that indicates capac-
itance change. Firmware can read the comparator state after
a pre-selected time to see if a large enough change has
occurred to trip the comparator in that time. This approach is
well suited to quickly detecting a capacitive button press.
Alternately, capacitance can be accurately measured by
going through the complete successive approximation pro-
cedure. The final IDAC setting gives a measurement of
capacitance.
The delay between starting the pin switching and reading
the comparator can be set by a firmware delay, or by using
the 6-bit counter in the TrueTouch logic to generate an inter-
rupt.
Figure 11-8. First Phase of Successive Approximation
TrueTouch Module
88
Comparator
Vr
M8C Read
Reference
IDAC
Buffer
Mux
Mux
I
OUT
Filter
LP
Vr
Conn. to
Ground
Closed
CSCLK
PSoC CY8CTMG20x and CY8CTST200 TRM, Document No. 001-53603 Rev. *C
C
INTERNAL
CS1
CS2
CSN
Figure 11-9. Second Phase of Successive Approximation
11.1.1.4
The negative charge integration method operates by initial-
izing an integration capacitor to a positive voltage, then dis-
connecting this driver. The integration capacitor voltage
decays through connection with an external sense capacitor
that is continuously switched between ground and the inte-
gration capacitor. The number of cycles required to reduce
the voltage on the integration capacitor to a target value
gives
Figure
The hardware supports the use of either pin P0[1] or P0[3]
for the external integration capacitor.
Comparator
Vr
Reference
M8C Read
IDAC
11-10.
a
Buffer
measure
Negative Charge Integration
Mux
Mux
I
OUT
Filter
LP
of
Vr
the
Conn. to
Closed
sense
Bus
CSCLK
capacitance.
C
INTERNAL
CS1
CS2
CSN
See
[+] Feedback