AT83C51SND1C_03 ATMEL [ATMEL Corporation], AT83C51SND1C_03 Datasheet - Page 39
AT83C51SND1C_03
Manufacturer Part Number
AT83C51SND1C_03
Description
Single-Chip Flash Microcontroller with MP3 Decoder and Human Interface
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT83C51SND1C_03.pdf
(210 pages)
- Current page: 39 of 210
- Download datasheet (2Mb)
External Interrupts
INT1:0 Inputs
KIN3:0 Inputs
Input Sampling
4109E–8051–06/03
External interrupts INT0 and INT1 (INTn, n = 0 or 1) pins may each be programmed to
be level-triggered or edge-triggered, dependent upon bits IT0 and IT1 (ITn, n = 0 or 1) in
TCON register as shown in Figure 22. If ITn = 0, INTn is triggered by a low level at the
pin. If ITn = 1, INTn is negative-edge triggered. External interrupts are enabled with bits
EX0 and EX1 (EXn, n = 0 or 1) in IEN0. Events on INTn set the interrupt request flag IEn
in TCON register. If the interrupt is edge-triggered, the request flag is cleared by hard-
ware when vectoring to the interrupt service routine. If the interrupt is level-triggered, the
interrupt service routine must clear the request flag and the interrupt must be deas-
serted before the end of the interrupt service routine.
INT0 and INT1 inputs provide both the capability to exit from Power-down mode on low
level signals as detailed in section “Exiting Power-down Mode”, page 48.
Figure 22. INT1:0 Input Circuitry
External interrupts KIN0 to KIN3 provide the capability to connect a matrix keyboard. For
detailed information on these inputs, refer to section “Keyboard Interface”, page 179.
External interrupt pins (INT1:0 and KIN3:0) are sampled once per peripheral cycle (6
peripheral clock periods) (see Figure 23). A level-triggered interrupt pin held low or high
for more than 6 peripheral clock periods (12 oscillator in standard mode or 6 oscillator
clock periods in X2 mode) guarantees detection. Edge-triggered external interrupts
must hold the request pin low for at least 6 peripheral clock periods.
Figure 23. Minimum Pulse Timings
INT0/1
Level-Triggered Interrupt
Edge-Triggered Interrupt
TCON.0/2
IT0/1
0
1
1 cycle
> 1 Peripheral Cycle
> 1 Peripheral Cycle
TCON.1/3
IE0/1
1 cycle
1 cycle
AT8xC51SND1C
IEN0.0/2
EX0/1
INT0/1
Interrupt
Request
39
Related parts for AT83C51SND1C_03
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64K Bytes In-System Programmable Programmable
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: