AM79C970A Advanced Micro Devices, AM79C970A Datasheet - Page 91
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
AM79C970A
Manufacturer Part Number
AM79C970A
Description
PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C970A.pdf
(219 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM79C970ACK
Manufacturer:
AMD
Quantity:
271
Company:
Part Number:
AM79C970AKC
Manufacturer:
AMtek
Quantity:
11
Part Number:
AM79C970AKC
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
226
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKCW
Manufacturer:
AMD
Quantity:
6 557
Part Number:
AM79C970AVC
Manufacturer:
AMD
Quantity:
20 000
The PCnet-PCI II controller will always read four bytes
for every host Expansion ROM read access. The inter-
face to the Expansion ROM runs synchronous to the
PCI bus interface clock. The PCnet-PCI II controller will
start the read operation to the Expansion ROM by driv-
ing the upper 8-bits of the Expansion ROM address on
ERA[7:0]. This happens in the same clock cycle that the
device claims the transfer by asserting DEVSEL. One
clock later, EROE is asserted and ERACLK goes high to
allow latching of the upper address bits externally. The
upper portion of the Expansion ROM address will be the
same for all four byte read cycles. ERACLK is asserted
for one clock. ERA[7:0] are driven with the upper 8-bits
of the Expansion ROM address for one more clock cycle
after ERACLK goes low. Next, the PCnet-PCI II control-
ler starts driving the lower 8 bits of the Expansion ROM
address on ERA[7:0].
The time the PCnet-PCI II controller waits for data to be
valid is programmable. ROMTMG (BCR18, bits 15–12)
defines the time from when the PCnet-PCI II controller
drives ERA[7:0] with the lower 8-bits of the Expansion
ROM address to when the PCnet-PCI II controller
latches in the data on the ERD[7:0] inputs. The register
value specifies the time in number of clock cycles. When
EROE
CE
Figure 39. Expansion ROM Interface
OE
ERACLK
P R E L I M I N A R Y
Expansion ROM
PCnet–PCI II
Am79C970A
A[15:8]
Latch
ROMTMG is set to Nine (the default value), ERD[7:0] is
sampled with the next rising edge of CLK nine clock cy-
cles after ERA[7:0] was driven with a new address
value. The clock edge that is used to sample the data is
also the clock edge that generates the next Expansion
ROM address. Only the first three bytes of Expansion
ROM data are stored in holding registers. The fourth
byte is passed directly from the ERD[7:0] inputs to the
AD[31:24] outputs. One clock cycle after the last data
byte is available, PCnet-PCI II controller asserts TRDY.
Two clock cycles after the data is transferred on the PCI
bus, EROE is deasserted.
The access time for the Expansion ROM device (t
can be calculated by subtracting the clock to output de-
lay for the ERA[7:0] outputs (t
clock setup time for the ERD[7:0] inputs (t
the time defined by ROMTMG:
t
For an adapter card application, the value used for clock
period should be 30 ns to guarantee correct interface
timing at the maximum clock frequency of 33 MHz.
ERA[7:0]
ACC
A[7:0]
ROMTMG* clock period – t
ERD[7:0]
D[7:0]
VAL
(ERA)) and the input to
VAL
(ERA) – t
SU
(ERD)) from
AMD
SU
19436A-42
(ERD)
ACC
91
)