OM11077 NXP Semiconductors, OM11077 Datasheet - Page 579
OM11077
Manufacturer Part Number
OM11077
Description
MODULE DIMM LPC2478 ARM7
Manufacturer
NXP Semiconductors
Specifications of OM11077
Accessory Type
Module Card
For Use With/related Products
ARM-57TS-LPC2478
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-4742
- Current page: 579 of 792
- Download datasheet (5Mb)
NXP Semiconductors
UM10237_4
User manual
7.2 Address Register I2ADDR
7.3 Comparator
7.4 Shift register I2DAT
7.5 Arbitration and synchronization logic
This register may be loaded with the 7 bit slave address (7 most significant bits) to which
the I
(GC) is used to enable general call address (0x00) recognition.
The comparator compares the received 7 bit slave address with its own slave address (7
most significant bits in I2ADR). It also compares the first received 8 bit byte with the
general call address (0x00). If an equality is found, the appropriate status bits are set and
an interrupt is requested.
This 8 bit register contains a byte of serial data to be transmitted or a byte which has just
been received. Data in I2DAT is always shifted from right to left; the first bit to be
transmitted is the MSB (bit 7) and, after a byte has been received, the first bit of received
data is located at the MSB of I2DAT. While data is being shifted out, data on the bus is
simultaneously being shifted in; I2DAT always contains the last byte present on the bus.
Thus, in the event of lost arbitration, the transition from master transmitter to slave
receiver is made with the correct data in I2DAT.
In the master transmitter mode, the arbitration logic checks that every transmitted logic 1
actually appears as a logic 1 on the I
1 and pulls the SDA line low, arbitration is lost, and the I
from master transmitter to slave receiver. The I
pulses (on SCL) until transmission of the current serial byte is complete.
Arbitration may also be lost in the master receiver mode. Loss of arbitration in this mode
can only occur while the I
Arbitration is lost when another device on the bus pulls this signal LOW. Since this can
occur only at the end of a serial byte, the I
Figure 22–118
Fig 118. Arbitration procedure
2
C block will respond when programmed as a slave transmitter or receiver. The LSB
(1) A device transmits serial data.
(2) Another device overrules a logic 1 (dotted line), transmitted by this I
(3) This I
line low. Arbitration is lost, and this I
transmitted. This I
the new master once it has won arbitration.
SDA line
SCL line
2
C is in Slave Receiver mode but still generates clock pulses until the current byte has been
shows the arbitration procedure.
Rev. 04 — 26 August 2009
2
C will not generate clock pulses for the next byte. Data on SDA originates from
2
C block is returning a “not acknowledge: (logic 1) to the bus.
(1)
1
(1)
2
2
C bus. If another device on the bus overrules a logic
2
C enters Slave Receiver mode.
(2)
3
2
Chapter 22: LPC24XX I
C block generates no further clock pulses.
2
C block will continue to output clock
4
2
C block immediately changes
(3)
2
C master, by pulling the SDA
8
2
C interfaces I
UM10237
© NXP B.V. 2009. All rights reserved.
ACK
9
579 of 792
2
C0/1/2
Related parts for OM11077
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: