ST72F324BJ6B6 STMicroelectronics, ST72F324BJ6B6 Datasheet - Page 120

• Manufacturer Part Number: ST72F324BJ6B6
• Description: MCU 8BIT 32KB FLASH/ROM 42-SDIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324BJ6B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Controller Family/series: ST7
• No. Of I/o's: 32
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• No. Of Pwm Channels: 3
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5589-5

On-chip peripherals
10.5.5
10.5.6
10.5.7
120/193
Low power modes
Table 60.
Interrupts
The SCI interrupt events are connected to the same interrupt vector.
These events generate an interrupt if the corresponding Enable Control bit is set and the
interrupt mask in the CC register is reset (RIM instruction).
Table 61.
SCI registers
SCI status register (SCISR)
Table 62.
Transmit data register empty
Transmission complete
Received data ready to be read
Overrun error detected
Idle line detected
Parity error
SCISR
Bit Name
Mode
Wait
7
Halt
TDRE
RO
7
TDRE
Interrupt event
No effect on SCI.
SCI interrupts cause the device to exit from Wait mode.
SCI registers are frozen.
In Halt mode, the SCI stops transmitting/receiving until Halt mode is exited.
Effect of low power modes on SCI
SCI interrupt control/wakeup capability
SCISR register description
Transmit Data Register Empty
This bit is set by hardware when the content of the TDR register has been transferred
into the shift register. An interrupt is generated if the TIE bit = 1 in the SCICR2
register. It is cleared by a software sequence (an access to the SCISR register
followed by a write to the SCIDR register).
0: Data is not transferred to the shift register.
1: Data is transferred to the shift register.
Note: Data will not be transferred to the shift register unless the TDRE bit is cleared.
RO
TC
6
RDRF
RO
5
Event flag Enable control bit Exit from Wait
RDRF
TDRE
IDLE
OR
TC
PE
IDLE
RO
4
Description
Function
TCIE
ILIE
RIE
PIE
TIE
OR
RO
3
RO
NF
2
Reset value: 1100 0000 (C0h)
Yes
Yes
Yes
Yes
Yes
Yes
RO
FE
1
Exit from Halt
ST72324Bxx
No
No
No
No
No
No
RO
PE
0