ST72F324BJ6B6 STMicroelectronics, ST72F324BJ6B6 Datasheet - Page 34

• Manufacturer Part Number: ST72F324BJ6B6
• Description: MCU 8BIT 32KB FLASH/ROM 42-SDIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324BJ6B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-SDIP (0.600", 15.24mm)
• Controller Family/series: ST7
• No. Of I/o's: 32
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• No. Of Pwm Channels: 3
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5589-5

Supply, reset and clock management
6.4
Caution:
6.4.1
34/193
Reset sequence manager (RSM)
The reset sequence manager includes three reset sources as shown in
●
●
●
These sources act on the RESET pin and it is always kept low during the delay phase.
The reset service routine vector is fixed at addresses FFFEh-FFFFh in the ST7 memory
map.
The basic reset sequence consists of three phases as shown in
●
●
●
When the ST7 is unprogrammed or fully erased, the Flash is blank and the RESET vector is
not programmed. For this reason, it is recommended to keep the RESET pin in low state
until programming mode is entered, in order to avoid unwanted behavior.
The 256 or 4096 CPU clock cycle delay allows the oscillator to stabilize and ensures that
recovery has taken place from the reset state. The shorter or longer clock cycle delay
should be selected by option byte to correspond to the stabilization time of the external
oscillator used in the application.
The reset vector fetch phase duration is two clock cycles.
Figure 13. Reset sequence phases
Asynchronous external RESET pin
The RESET pin is both an input and an open-drain output with integrated R
resistor. This pull-up has no fixed value but varies in accordance with the input voltage. It
can be pulled low by external circuitry to reset the device. See the
section for more details.
A reset signal originating from an external source must have a duration of at least t
in order to be recognized (see
MCU can enter reset state even in Halt mode.
External reset source pulse
Internal LVD reset
Internal Watchdog reset
Active Phase depending on the reset source
256 or 4096 CPU clock cycle delay (selected by option byte)
Reset vector fetch
ACTIVE PHASE
Figure
256 or 4096 CLOCK CYCLES
15). This detection is asynchronous and therefore the
INTERNAL RESET
RESET
Figure
Electrical characteristics
VECTOR
13:
Figure
FETCH
ON
ST72324Bxx
weak pull-up
14:
h(RSTL)in