MC9S12NE64VTU Freescale Semiconductor, MC9S12NE64VTU Datasheet - Page 274

• Manufacturer Part Number: MC9S12NE64VTU
• Description: IC MCU 25MHZ ETHERNET/PHY 80TQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12NE64VTU

• Mfg Application Notes: MC9S12NE64 Integrated Ethernet Controller Implementing an Ethernet Interface with the MC9S12NE64 Web Server Development with MC9S12NE64 and Open TCP
• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 3.465 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 80-TQFP Exposed Pad, 80-eTQFP, 80-HTQFP, 80-VQFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 16 bit
• Operating Supply Voltage: - 0.3 V to + 3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 65 C
• On-chip Adc: 10 bit
• For Use With: EVB9S12NE64E - BOARD EVAL FOR 9S12NE64DEMO9S12NE64E - DEMO BOARD FOR 9S12NE64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 9 Serial Peripheral Interface (SPIV3)
9.4.3
During an SPI transmission, data is transmitted (shifted out serially) and received (shifted in serially)
simultaneously. The serial clock (SCK) synchronizes shifting and sampling of the information on the two
serial data lines. A slave select line allows selection of an individual slave SPI device, slave devices that
are not selected do not interfere with SPI bus activities. Optionally, on a master SPI device, the slave select
line can be used to indicate multiple-master bus contention.
9.4.3.1
Using two bits in the SPI Control Register1, software selects one of four combinations of serial clock phase
and polarity.
The CPOL clock polarity control bit specifies an active high or low clock and has no significant effect on
the transmission format.
The CPHA clock phase control bit selects one of two fundamentally different transmission formats.
Clock phase and polarity should be identical for the master SPI device and the communicating slave
device. In some cases, the phase and polarity are changed between transmissions to allow a master device
to communicate with peripheral slaves having different requirements.
9.4.3.2
The first edge on the SCK line is used to clock the first data bit of the slave into the master and the first
data bit of the master into the slave. In some peripherals, the first bit of the slave’s data is available at the
slave’s data out pin as soon as the slave is selected. In this format, the first SCK edge is issued a half cycle
after SS has become low.
A half SCK cycle later, the second edge appears on the SCK line. When this second edge occurs, the value
previously latched from the serial data input pin is shifted into the LSB or MSB of the shift register,
depending on LSBFE bit.
After this second edge, the next bit of the SPI master data is transmitted out of the serial data output pin of
the master to the serial input pin on the slave. This process continues for a total of 16 edges on the SCK
line, with data being latched on odd numbered edges and shifted on even numbered edges.
274
Transmission Formats
Clock Phase and Polarity Controls
CPHA = 0 Transfer Format
SHIFT REGISTER
GENERATOR
BAUD RATE
MASTER SPI
Figure 9-8. Master/Slave Transfer Block Diagram
MC9S12NE64 Data Sheet, Rev. 1.1
MISO
MOSI
SCK
SS
V
DD
MISO
MOSI
SCK
SS
SHIFT REGISTER
SLAVE SPI
Freescale Semiconductor