MC9S12E128CFU Freescale Semiconductor, MC9S12E128CFU Datasheet - Page 345

• Manufacturer Part Number: MC9S12E128CFU
• Description: IC MCU 128K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E128CFU

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 16 bit
• Operating Supply Voltage: 3.135 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• On-chip Dac: 8 bit, 2 Channel
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

11.3.2.20 PMF Enable Control A Register (PMFENCA)
Read and write anytime.
Freescale Semiconductor
Module Base + 0x0020
PWMRIEA
PWMENA
LDOKA
Reset
Field
7
1
0
W
R
PWMENA
PWM Generator A Enable — When MTG is clear, this bit when set enables the PWM generators A, B and C
and the PWM0–5 pins. When PWMENA is clear, PWM generators A, B and C are disabled, and the PWM0–5
pins are in their inactive states unless the corresponding OUTCTLx bits are set.
When MTG is set, this bit when set enables the PWM generator A and the PWM0 and PWM1 pins. When
PWMENA is clear, the PWM generator A is disabled and PWM0 and PWM1 pins are in their inactive states
unless the OUTCTL0 and OUTCTL1 bits are set.
0 PWM generator A and PWM0–1 (2–5 if MTG=0) pins disabled unless the respective OUTCTL bit is set.
1 PWM generator A and PWM0–1 (2–5 if MTG=0) pins enabled.
Load Okay A — When MTG is clear, this bit allows loads of the PRSCA bits, the PMFMODA register and the
PWMVAL0–5 registers into a set of buffers. The buffered prescaler A divisor, PWM counter modulus A value, and
all PWM pulse widths take effect at the next PWM reload.
When MTG is set, this bit allows loads of the PRSCA bits, the PMFMODA register and the PWMVAL0–1 registers
into a set of buffers. The buffered prescaler divisor A, PWM counter modulus A value, PWM0–1 pulse widths take
effect at the next PWM reload.
Set LDOKA by reading it when it is logic zero and then writing a logic one to it. LDOKA is automatically cleared
after the new values are loaded, or can be manually cleared before a reload by writing a logic zero to it. Reset
clears LDOKA.
0 Do not load new modulus A, prescaler A, and PWM0–1 (2–5 if MTG=0) values
1 Load prescaler A, modulus A, and PWM0–1 (2–5 if MTG=0) values
Note: Do not set PWMENA bit before setting the LDOKA bit and do not clear the LDOKA bit at the same time as
PWM Reload Interrupt Enable A — This bit enables the PWMRFA flag to generate CPU interrupt requests.
0 PWMRFA CPU interrupt requests disabled
1 PWMRFA CPU interrupt requests enabled
0
7
setting the PWMENA bit.
= Unimplemented or Reserved
Figure 11-26. PMF Enable Control A Register (PMFENCA)
0
0
6
Table 11-25. PMFENCA Field Descriptions
MC9S12E128 Data Sheet, Rev. 1.07
0
0
5
Chapter 11 Pulse Width Modulator with Fault Protection (PMF15B6CV2)
0
0
4
Description
0
0
3
0
0
2
LDOKA
0
1
PWMRIEA
0
0
345